Bradley Smoker S19-310SS Installation Instructions, Supplies Required, Secure base to floor

Page 3

Installation

S19-310SS

Installation Instructions

Supplies Required:

•(3) 3/8" floor anchors and bolts

•Piping to 1-1/4" BSP water supply inlet

•Adequate supply pipe supports

•Piping to 1-1/4" IPS drain outlet on unit

•Minimum 4" drain to accommodate 30 gallons per minute discharge for drench shower waste

•OPTIONAL: sign mounting hardware

Step 1: Secure base to floor

1. Install three suitable anchors (by installer)

for 3/8" bolts in the floor (see Figure 1).

Ø10-3/4"

(273mm)

9" (229mm)

 

9" (229mm) DIA. FLANGE

 

WITH (3) 3/8"DIA. HOLES

10-1/2"

ON AN 8" (203mm)

DIA. BOLT CIRCLE

(266mm)

 

26-3/8"

5-1/8"(670mm) (130mm)

2. Bolt the base to the floor anchors using 3/8"

bolts (supplied by installer).

Step 2: Assemble eyewash components

1.Assemble the remaining unit components as shown in Figure 2 on page 4.

•Apply pipe sealant or tape (supplied by installer) to all male-threaded pipe joints.

•Use rubber grip pad or strap wrench around pipes when tightening to prevent marring. Place grip pad on pipe and then put wrench over grip pad. With grip pad in place, turn pipe with wrench.

•The bottom edge of the showerhead should be 7'-1" (2160mm) from floor.

2. When connecting steel chain, first connect

chain to foot treadle “S” hook. Then with

foot treadle raised up, straighten chain and

connect a link to “S” hook on valve handle.

24"

(610mm)

Ø10-3/4"

(273mm)

7'-1"

(2160mm)

TO

FLOOR

6" (152mm)

6"

(152mm)

66" (1676mm)

TO

FLOOR 36-3/8" (924mm)

Make sure steel chain is pulled tight. The

length of chain used will vary.

IMPORTANT: Do not rely on Bradley’s Combination Unit to support supply piping.

Step 3: Connect water supply

NOTE: All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1/8" (3mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 1/8" (3mm).

Figure 1

1.Connect water supply piping to 1-1/4" IPS inlet on unit (piping supplied by installer). Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or other means.

2.Connect drain piping to 1-1/4" IPS drain outlet on unit (piping supplied by installer).

3.Hang the safety sign from the unit with the curtain hooks provided (or mount it to the wall using sign-mounting hardware supplied by installer).

Bradley Corporation • 215-533 Rev. U; EN 06-532G

6/26/07

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Table of Contents Table des matièresContenido S19-310SS Installation Assemble eyewash components Installation InstructionsSupplies Required Secure base to floorAssembly of Components Qty Description Parts ListAvertissement Étape 2 Montage Instructions d’installationFournitures Étape 1 Fixation de la base au solAssemblage des composantes Alimentation 4 IPSCe bout Piéce Réf Qté Description Liste des piècesAdvertencia Paso 2 Montar los componentes Instrucciones de instalaciónMateriales necesarios Paso 1 Afianzar la base al pisoControl Armado de los componentesNota Si el acoplamiento en T se usa como entrada Utilizar el tapón artículo NºArt Pieza No Cant Descripción Lista de piezas

S19-310SS specifications

The Bradley Smoker S19-310SS is a standout choice for both amateur and experienced smokers looking to elevate their culinary skill set. Crafted with a blend of aesthetics and functionality, this top-of-the-line electric smoker offers a variety of features that ensure perfect results every time.

One of the essential features of the S19-310SS is its dual-wall construction, which provides excellent insulation and maintains a consistent temperature throughout the smoking process. This design not only enhances heat retention but also improves energy efficiency, allowing users to enjoy long smoking sessions without worrying about fluctuating temperatures.

A key technology integrated into the S19-310SS is its digital control system, which allows for precise temperature adjustments and cooking times. With an easy-to-read LED display, users can monitor the internal conditions of the smoker without opening the door, thereby preventing heat loss. This level of control is crucial when aiming for the perfect smoke flavor, ensuring meats and fish achieve the ideal level of tenderness and flavor infusion.

The Bradley Smoker S19-310SS also comes equipped with an innovative wood bisquette feeding system. This unique feature automatically feeds wood bisquettes into the smoke generator, ensuring a steady and consistent smoke output. The use of wood bisquettes results in clean smoke, minimizing the risk of creosote buildup and imparting a rich, authentic flavor to the food. With a variety of wood flavors available, from hickory to cherry, users can experiment and customize their smoking experience according to personal preference.

Furthermore, the spacious interior of the S19-310SS allows for multiple racks, enabling users to smoke a variety of foods simultaneously. This increased capacity is perfect for gatherings, family meals, or meal prep, catering to both small and large groups alike.

The design of the S19-310SS is user-friendly, featuring a front-access door that simplifies loading and unloading without interrupting the cooking process. Additionally, its stainless steel exterior provides durability and resistance to the elements, making it suitable for outdoor use.

In conclusion, the Bradley Smoker S19-310SS is a powerful electric smoker that combines innovative technology with user-friendly features. Whether you are smoking meats, fish, or vegetables, this smoker delivers consistent results and exceptional flavor, making it an indispensable tool for any barbecue enthusiast.
Top Page Image Contents