Bolens 589 manual Maintaining Your Lawn Mower, Engine, Deck, Cutting Blade

Page 13

SECTION 7: MAINTAINING YOUR LAWN MOWER

WARNING: Be sure to disconnect the spark plug wire and DE-ENERGIZE starter

before performing any repairs or maintenance. DO NOT attempt any maintenance or service to the engine and/or mower equipped with the safety key in the unlocked and/or energized mode.

NEVER assume starter is de-energized, even if the key is in the locked position and/or removed from the engine. ALWAYS de- energize self starter prior to performing any maintenance or service to the engine and/or mower. Follow instructions on the engine and/or machine to de-energize starter.

Engine

NOTE: When tipping the unit, empty the fuel tank and keep the spark plug side of engine up. Never tip the mower more than 90 degrees and do not leave the mower tipped for any length of time. Oil can drain into the upper part of the engine causing a starting problem.

Refer to the engine manual for all engine maintenance instructions.

•Maintain engine oil as instructed in the engine manual. Check oil level before starting mower.

•Service air cleaner every 25 hours under normal conditions. Poor engine performance and flooding usually indicate that the air cleaner should be serviced. To service the air cleaner, refer to the engine manual.

•The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each mowing season.

Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all grass, dirt, and combustible debris from muffler area.

Deck

The underside of the mower deck should be cleaned after each use to prevent a buildup of grass clippings, leaves, dirt, or other matter. If this debris is allowed to accumulate, it will invite rust and corrosion, and may prevent proper mulching, discharge, or bagging. The deck may be cleaned by tilting the mower and scraping clean with a suitable tool (make certain the spark plug wire is disconnected).

IMPORTANT: We do not recommend the use of a pressure washer or garden hose to clean your unit. The use of water will result in shorter life and less serviceability.

Cutting Blade

•When removing the cutting blade for sharpening or replacement, protect your hands with a pair of heavy gloves or use a heavy rag to hold the blade.

To Remove Blade

•Remove the bolt and the blade bell support which hold the blade and the blade adapter to the engine crankshaft. See Figure 13.

•Remove the blade and the adapter from the crankshaft.

Blade

Adapter

Blade Bell

Support

Hex Bolt

Figure 13

WARNING: Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when necessary.

•When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade.

WARNING: An unbalanced blade will cause excessive vibration when rotating at high speeds. It may damage the mower, and/ or cause personal injury.

•The blade can be tested by balancing it on a round shaft screwdriver. Remove metal from the heavy side until it balances evenly. It is recommended that the blade always be removed from the adapter when testing for balance. Before reinstalling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the blade adapter with light oil.

To Reinstall Blade

•Be sure to install the blade with the side marked “Bottom” (or with part number) facing the ground when the mower is in the operating position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesSlope Operation ServiceChildren Your Responsibility Slope Gauge Assembling Your Lawn Mower Disconnecting Spark Plug WireRemoving Unit From Carton Hardware PackAssembling Grass Catcher Attaching Starter RopeAttaching Grass Catcher To Mower Converting To MulcherKnow Your Lawn Mower Operating Your Lawn Mower To Stop Engine And Blade Using Your Lawn MowerTo De-Energize Self Starter Throttle SpeedCutting Height Engine AdjustmentsHandle Height Engine Maintaining Your Lawn MowerDeck Cutting BladeReplacing Rear Flap LubricationProblem Cause Remedy TroubleshootingParts List for Model Part Description Model 589 SeriesMTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone MANUFACTURER’S Limited Warranty for

589 specifications

The Bolens 589 is a versatile riding lawn mower that captures the essence of performance, durability, and user-friendly design. Built to meet the needs of both residential homeowners and landscaping professionals, this machine is equipped with features that optimize mowing efficiency and enhance user experience.

One of the standout characteristics of the Bolens 589 is its powerful engine. It typically features a robust 19 to 20 horsepower engine that ensures efficient cutting power, making it suitable for larger lawns and rugged terrains. This powerful engine is paired with a reliable automatic transmission that provides smooth and easy maneuverability, allowing users to tackle various yard sizes without difficulty.

The cutting deck on the Bolens 589 is designed for precision and durability. With a width ranging from 42 to 46 inches, it is capable of making quick work of grass while leaving a clean, professional finish. The deck is made from heavy-duty steel, ensuring it can withstand the rigors of regular use. Additionally, the deck height can typically be adjusted to suit different grass types and cutting conditions, giving users the flexibility they need for various lawn care tasks.

In terms of comfort, the Bolens 589 is built with the operator in mind. It features a plush, adjustable seat that provides support during extended mowing sessions. The controls are intuitively placed, allowing for effortless operation and quick adjustments while driving. Enhanced visibility from the driver's seat is another design consideration that bolsters safety and effectiveness when mowing in tight spaces.

Innovation is evident in the Bolens 589 with its inclusion of modern technologies. Some models may include features like LED headlights for improved visibility during early morning or late evening mowing sessions, and mulching capabilities that allow for finer grass clippings that can be left on the lawn as natural fertilizer.

Moreover, the Bolens 589 often showcases a durable frame to withstand seasonal changes and heavy use. Its robust construction not only extends the life of the equipment but also ensures stability on uneven surfaces. Combined with a user-friendly maintenance system, the Bolens 589 makes upkeep simple and efficient, allowing owners to focus more on lawn care.

Overall, the Bolens 589 is a well-rounded riding lawn mower that excels in providing power, comfort, and ease of use. With its combination of features and technologies, it stands as a strong contender in the market, meeting the diverse needs of grass enthusiasts and professionals alike.
Top Page Image Contents