Magnavox MRD300 owner manual Troubleshooting, No picture

E n g l i s h

Troubleshooting

WARNING!

Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock.

If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to solve a problem by following these hints, consult your dealer or call 1800-705-2000.

Problem			Solution
	No power.	–	Check if the AC power cord is properly connected.
	No picture.	–	Check if the TV is switched on.
		– Check the video connection.
		– Press DVD button on the system.
		– Set your TV to the correct Video In channel. These channels are usually near channel 00. Or,
			you may have a button on the TV remote control that selects Auxiliary or A/V IN channel. See
			your TV owner’s manual for details. Or, change channels at the TV until you see DVD screen
			on the TV.
	Distorted or poor picture.	–	Sometimes a small amount of picture distortion may appear. This is not a malfunction.
		–	Clean the disc.
		– Check the video connection. You cannot use S-Video and Component Video connections at
			the same time.
	Completely distorted picture or	–	Make sure the NTSC/PAL setting at the DVD system matches the video signal of your
	black/white picture.		television (see “System Setup (DVD) - Selecting the color system that matches the connected
			TV”).
	The aspect ratio of the screen	–	The aspect ratio is fixed on the DVD disc.
	cannot be changed even though	–	Depending on the TV, it may not be possible to change the aspect ratio.
	you have set the TV display.
	No sound or distorted sound.	–	Adjust the volume.
		– Check that the speakers are connected correctly.
		– Replace the speaker cables.
		– Check the speaker settings.
		– The system is in pause, slow motion or fast forward/reverse mode, press PLAY to resume
			normal play mode.
	The DVD player does not	–	Insert a readable disc with the playback side facing down.
	start playback.	–	Check the disc type, color system and regional code. Check for any scratches or smudges on
			the disc.
		– Press SETUP to turn off the setup menu screen.
		– Cancel the parental control rating function or change the rating level.
		– Moisture has condensed inside the system. Remove the disc and leave the system turned on
			for about an hour..
	The DVD system does not respond	–	Disconnect the power plug from the outlet and insert again.
	when the buttons are pressed.
	Cannot activate some features,	–	Multi-language sound or subtitle is not recorded on the DVD.
	such as Angles, Subtitles, or	–	Changing the language for the sound or subtitle is prohibited on the DVD.
	multi-language Audio.	–	The features may not be available on the disc.
	No image is output when a	–	Make sure the component is connected correctly.
	function is selected.	–	Press the correct function button for the input source.
	Considerable noise in radio	–	Tune in to the correct frequency.
	broadcasts.	–	Connect the antenna.
		– Route RF (AC-3) and digital cables away from the antenna terminals and wires.
		– Fully extend the FM wire antenna. Position for best reception and secure to a wall.
		– Connect an outdoor FM or AM antenna.
		– Adjust the direction and position for best reception.
		– Turn off the equipment causing the noise or move it away from the DVD system.
		– Place the antenna farther away from any equipment that may be causing the noise.
	The remote control does not	–	Point the remote control at the remote sensor of the unit.
	function.	–	Reduce the distance to the player.
		– Remove any possible obstacles.
		– Replace the batteries with new ones.
		– Check that the batteries are loaded correctly.
	The display is dark.	–	Press DIM again.
	Low hum or buzz sound.	–	Place the DVD system as far away as possible from electrical devices that may be causing
			interference.
	Low bass response.	–	Check all speakers for correct polarity.

26TROUBLESHOOTING