Features, Assembly | Black & Decker GLC1825L, GLC1423L specification

Chargers

uUse your Black & Decker charger only to charge the battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage.

uNever attempt to charge non-rechargeable batteries.

uHave defective cords replaced immediately.

uDo not expose the charger to water.

uDo not open the charger.

uDo not probe the charger.

$The charger is intended for indoor use only. Read the instruction manual before use.

#Your charger is double insulated; therefore no earth wire is required. Always check that the mains voltage corresponds to the voltage on the rating plate. Never attempt to replace the charger unit with a regular mains plug.Electrical safety

uIf the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.

Features

This appliance includes some or all of the following features.

1.On/off switch

2.Handle

3.Lock off button

4.Battery

5.Second handle

6.Guard

7.Spool housing

8.Head

9.Edge guide

Assembly

Warning! Before assembly, make sure that the tool is switched off and unplugged.

Fitting the guard (fig. A-B)

uRemove the screw from the guard.

uKeeping the guard (6) square to the strimmer head (8) slide it into place until the retaining tab clicks into place (Ensure that the guide rails (10) on the guard (6) are correctly aligned with the guide rails (11) on the strimmer head (8). fig. A).

(Original instructions)

ENGLISH

uSecure the guard (6) with the screw (12).

Warning! Never use the tool unless the guard is properly fitted.

Attaching the second handle (fig. C)

uPress in and hold both of the buttons (14) on the side of the handle.

uSlide the second handle (5) in place over the buttons (14). Warning! Ensure that the teeth on the button are correctly aligned in slots in the handle and that the handle is secure.

Adjusting the position of the secondary handle (fig. D)

The second handle (5) can be adjusted to provide optimum balance and comfort.

uPress in the button (15) on the left side od the handle.

uRotate the second handle (5) into the required position.

uRelease the button (15).

Warning! Ensure that the teeth on the button are correctly aligned in slots in the handle and that the handle is secure.

Adjusting the height of the tool (fig. E)

This tool has a telescopic mechanism, allowing you to set it to a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

uDisconnect the tool from the supply.

uLoosen the adjustment collar (16) by turning it clockwise.

uGently pull the tube (17) in or out of the handle (2) to the desired height.

uTighten the adjustment collar (16) by turning anti- clockwise.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing. Warning! Before assembly, remove the battery from the tool.

uRemove the tape holding the cutting line to the spool housing (7).

Fitting and removing the battery (fig. F)

uTo fit the battery (4), line it up with the receptacle on the tool. Slide the battery into the receptacle and push until the battery snaps into place.

uTo remove the battery, push the release button (19) while at the same time pulling the battery out of the receptacle.

GLC1423L, GLC1825L specifications

The Black & Decker GLC1825L and GLC1423L are innovative cordless grass trimmers designed to meet the needs of homeowners and landscaping enthusiasts. These models combine efficiency, efficacy, and user-friendly features to provide a hassle-free trimming experience.

The GLC1825L model is equipped with an 18V lithium-ion battery that ensures extended runtime and quick charging. Its powerful motor delivers sufficient torque to tackle thick grass and overgrowth, making it suitable for various terrains. The adjustable cutting width, which can be set at either 25 cm or 30 cm, allows users to adapt the tool to their specific trimming requirements. The model is designed with a lightweight structure, making it easy to maneuver and reducing user fatigue during prolonged use.

On the other hand, the GLC1423L model features a slightly less powerful 14V lithium-ion battery. Although smaller in capacity, it still provides impressive performance, making it ideal for small to medium-sized gardens. The 23 cm cutting width strikes a balance between power and precision, ensuring efficient trimming without sacrificing control. Both models come with a built-in guide wheel that helps maintain straight lines and reduces the risk of damaging nearby plants or flower beds.

One of the signature technologies incorporated in both trimmers is the automatic feed spool, which eliminates manual line adjustment. This feature ensures that the cutting line is fed smoothly and consistently during operation, allowing users to maintain focus on their task without interruptions. The easy-to-use spool replacement system makes it convenient for users, further enhancing the overall experience.

Another key characteristic of the Black & Decker GLC series is their ergonomic design. These trimmers feature adjustable telescopic shafts and rotating handles that enable users to customize the tool to their comfort level. This adjustability helps prevent strain on the back and wrists, promoting a more natural working posture.

Both models also come equipped with safety features, such as an integrated safety switch and a protective guard. These features enhance user safety by minimizing the risk of accidental starts and ensuring that debris is kept at bay during operation.

In summary, the Black & Decker GLC1825L and GLC1423L grass trimmers exemplify modern gardening technology. With their combination of user-friendly features, powerful performance, and ergonomic design, they provide an excellent solution for anyone looking to keep their garden pristine and well-maintained. Whether for small trimming jobs or larger landscaping tasks, these cordless trimmers deliver dependability and ease of use.