uUnplug the tool.
uKeep the tabs (21) depressed and remove the spool cover
(22)from the housing (7).
uRemove the empty spool (23) from the housing.
uRemove any dirt and grass from the spool cover and housing.
uTake the new spool and push it onto the boss in the housing. Rotate the spool slightly until it is seated.
uUnclip the end of the cutting line and guide the line into the eyelet (24). The line should protrude approx. 11 cm from the spool cover.
uAlign the tabs (21) on the spool cover with the cut outs
(25)in the housing.
uPush the cover onto the housing until it snaps securely into place.
Warning! If the cutting lines protrude beyond the trimming blade (26), cut them off so that they just reach the blade.
Winding new line onto an empty spool (fig. N - P)
You may wind new cutting line onto an empty spool. Replacement packs of cutting line are available from your Black & Decker dealer (cat. no. A6170 (25 m), A6171 (40 m)).
uRemove the empty spool from the tool as described above.
uRemove any remaining cutting line from the spool.
uFeed 2 cm of cutting line into the hole (27) in the spool as shown (fig. N).
uBend the cutting line and anchor it in the
uWind the cutting line onto the spool in the direction of the arrow. Make sure to wind the line on neatly and in layers. Do not
uWhen the wound cutting line reaches the recesses (29), cut the line. Let the line protrude approx. 12 cm from the spool and hold a finger on the line to keep it in place (fig. O).
uProceed as described above to fit the spool on the tool. Warning! Only use the appropriate type of Black & Decker cutting line.
Troubleshooting
If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local Black & Decker repair agent.
Warning! Before proceeding, unplug the tool.
(Original instructions) | ENGLISH |
Automatic line feed does not work
uKeep the tabs depressed and remove the spool cover from the housing.
uPull the cutting line until it protrudes 11 cm from the housing. If insufficient cutting line is left on the spool, install a new spool of cutting line as instructed above.
uAlign the tabs on the spool cover with the cut outs in the housing.
uPush the cover onto the housing until it snaps securely into place.
uIf the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is jammed, try the following suggestions:
uCarefully clean the spool cover and housing.
uRemove the spool and check if the lever can move freely.
uRemove the spool and unwind the cutting line, then wind it on neatly again as described above. Replace the spool as instructed.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool/appliance care and regular cleaning.
Your charger does not require any maintenance apart from regular cleaning.
Warning! Before performing any maintenance on corded/ cordless power tools:
uSwitch off and unplug the appliance/tool.
uOr switch off and remove the battery from the appliance/ tool if the appliance/tool has a separate battery pack.
uOr run the battery down completely if it is integral and then switch off.
uUnplug the charger before cleaning it. Your charger does not require any maintenance apart from regular cleaning.
uRegularly clean the ventilation slots in your tool/appliance and charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth. Do not use any abrasive or
uRegularly clean the cutting line and spool using a soft brush or dry cloth.
uRegularly use a blunt scraper to remove grass and dirt from the underneath of the guard.
Appliance runs slowly
uCheck that the spool housing can rotate freely. Carefully clean it if necessary.
uCheck that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it just reaches the line trimming blade.
ZSeparate collection. This product must not be disposed of with normal household waste.Protecting the environment
9