Billy Goat FM3300IN, FM3300INE owner manual 7SOUND, 8VIBRATION

Page 2

5IN THE INTEREST OF SAFETY

BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & ENGINE MANUAL.”

THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

WARNING: DO NOT

1.DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

2.DO NOT place hands or feet near moving or rotating parts.

3.DO NOT store, spill or use gasoline near an open flame, or devices such as a stove, furnace, or water heater which use a pilot light or devices which can create a spark.

4.DO NOT refuel indoors where area is not well ventilated. Outdoor refueling is recom- mended.

5.DO NOT fill fuel tank while engine is running. Allow engine to cool for 2 minutes before refueling. Store fuel in approved safety containers.

6.DO NOT remove fuel tank cap while engine is running.

7.DO NOT operate engine when smell of gasoline is present or other explosive condi- tions exist.

8.DO NOT operate engine if gasoline is spilled. Move machine away from the spill and avoid creating any ignition until the gasoline has evaporated.

9.DO NOT transport unit with fuel in tank.

10.DO NOT smoke when filling fuel tank.

11.DO NOT choke carburetor to stop engine. Whenever possible, gradually reduce engine speed before stopping.

12.DO NOT run engine at excessive speeds. This may result in injury & /or damage to unit.

13.DO NOT tamper with governor springs, governor links or other parts which may change the governed engine speed.

14.DO NOT tamper with the engine speed selected by the engine manufacturer.

15.DO NOT check for spark with spark plug or spark plug wire removed. Use an approved tester.

16.DO NOT crank engine with spark plug removed. If engine is flooded, place throttle in “FAST” position and crank until engine starts.

17.DO NOT strike flywheel with a hard object or metal tool as this may cause flywheel to shatter in operation. Use proper tools to service engine.

18.DO NOT operate engine without a muffler. Inspect periodically and replace, if necessary. If engine is equipped with muffler deflector, inspect periodically and replace, if necessary, with correct deflector.

19.DO NOT operate engine with an accumula- tion of grass, leaves, dirt or other combustible material in the muffler area.

20.DO NOT use this engine on any forest covered, brush covered, or grass covered unimproved land unless a spark arrester is installed on the muffler. The arrester must be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands.

21.DO NOT touch hot muffler, cylinder, or fins

because contact may cause burns.

22.DO NOT run engine without air cleaner or air cleaner cover.

23.DO NOT operate during excessive vibra- tion!

24.DO NOT leave machine unattended while in operation.

25.DO NOT park machine on a steep grade or slope.

WARNING: DO

1.ALWAYS DO remove the wire from the spark plug when servicing the engine or equipment TO PREVENT ACCIDENTAL STARTING.

2.DO keep cylinder fins and governor parts

free of grass and other debris

which can

affect engine speed.

 

3.DO pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

4.DO examine muffler periodically to be sure it is functioning effectively. A worn or leaking muffler should be repaired or replaced as necessary.

5.DO use fresh gasoline. Stale fuel can gum carburetor and cause leakage.

6.DO check fuel lines and fittings frequently for cracks or leaks. Replace if necessary

7.Follow engine manufacturer operating and maintenance instructions.

8.Inspect machine and work area before starting unit.

6TABLE OF CONTENTS

SAFETY INSTRUCTIONS

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

GENERAL SAFETY

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

ASSEMBLY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LIT. BAG & CONTROLS

 

 

 

 

 

 

 

5

 

 

 

 

 

 

 

LABELS

 

 

 

 

 

 

5 - 6

 

 

 

 

 

OPERATION

 

 

 

 

 

 

 

 

 

 

6

- 9

 

 

 

 

 

 

 

 

 

 

MAINTENANCE

 

 

 

 

 

 

 

 

10

- 14

 

 

 

 

 

 

PARTS DRAWING & LIST

 

 

 

 

15

- 18

 

 

ACCESSORIES

 

 

19

 

 

TROUBLESHOOTING

 

 

 

 

20

 

 

 

 

WARRANTY PROCEDURE

 

 

20

 

 

7SOUND

Sound tests conducted were in accordance with 2000/14/EEC and were performed on 9/18/03 under the condition listed.

NOTE: Sound power level listed is the highest value for any model in this manual.

Please refer to serial plate on the unit for the sound level for your model.

Sound level of 95 dBA at operator position

 

 

 

GENERAL CONDITION:

Sunny

 

 

 

TEMPERATURE:

75 °F (23.9 °C)

 

 

 

 

 

 

 

 

 

WIND SPEED:

8.1 MPH (13.0 KPH)

 

 

 

 

100 dB

 

WIND DIRECTION:

South West

(FM3300IN MODEL)

 

63%

 

 

 

HUMIDITY:

 

 

BAROMETRIC PRESSURE:

29.9" Hg (759mm Hg)

8VIBRATION

VIBRATION LEVEL 1.8 g

Vibration levels at the operators handles were mea- sured in the vertical, lateral, and longitudinal directions using calibrated vibration test equipment. Tests were performed on 10/1/03 under the conditions listed:

GENERAL CONDITION:

Sunny

TEMPERATURE:

46 °F (7.8 °C)

WIND SPEED:

7.0 MPH (11.3 kmh)

WIND DIRECTION:

 

South West

HUMIDITY:

66%

BAROMETRIC PRESSURE:

30.4" Hg (772mm Hg)

Part No. 520166

Page 2 of 20

Form No. F112003A

Image 2
Contents Accessories 7SOUND 8VIBRATIONGeneral Safety Assembly Literature Assy ControlsPatent Pending Starting Cutting OperationCutting Height Adjustment Blade ClutchStorage PropulsionHandling & Transporting Maintenance Cable Adjustments Starter Switch WiringBelt Replacement Blade Removal / SharpeningSpindle Drive Belt Brake Puck Replacement FM3300INB, FM3300INEB Deck Assembly Parts DrawingEngine Assembly FM3300INB, FM3300INEBDrive Assembly Parts DrawingFM3300INB, FM3300INEB Handle Assembly Grass Catcher KIT Transaxle Guard KITTroubleshooting Problem Possible Cause Solution