Billy Goat FM3300IN, FM3300INE owner manual Spindle Drive Belt

Page 13

17MAINTENANCE continued

17.5BELT REPLACEMENT continued

Blade Drive Belt Replacement continued

13.Reinstall the left and right belt guide fingers under the engine base using all fasteners in the exact order they were removed.

NOTE: Before installing the fasteners inspect them for wear and replace as necessary.

14.Torque the four engine bolts to 40 ft-lbs.

Note: With clutch levers engaged, be sure belt guides do not touch belts after installation.

15.Observe the idler pulley when the blade drive lever is lowered and released (see figure 17-7).

NOTE: Idler should tighten the belt when blade drive lever is pressed and the belt should be slack when the lever is released. With the lever depressed, the edge of the belt guide should not rub on the belt.

16.Replace the cover

17.Reconnect spark plug wire.

18.Start engine and check for proper operation of blade drive system.

Figure 17-7

Spindle Drive Belt

Tools required: 3/8 inch socket, 1/2 inch socket.

1.Disconnect spark plug wire.

2.Follow steps to remove the Blade Drive Belt (on the spindle pulley side only) from the previous section.

3.Loosen the two idler plate nuts (Item 143).

4.Slide the belt idler to release the belt tension.

5.Observe the belt routing, then remove the old belt and install the new belt using the original routing.

6.Tension the belt using a long screwdriver or other pry bar to push the idler pulley against the belt.

Note: Take care not to damage the idler pulley.

7.Tighten the two idler plate nuts just enough to avoid slippage while checking the belt tension.

8.Check belt deflection. Finger pressure should give 0.5” to 0.75” (see figure 17-8).

9.Increase/decrease belt tension for proper deflection.

10.Finish Tightening the two idler plate nuts.

11.Follow steps to reinstall Blade Drive Belt from the previous section.

11.Replace cover.

12.Reconnect spark plug wire.

Figure 17-8

Transaxle Drive Belt Replacement

Tools required: 1/2 Wrench or ratchet and 1/2 inch socket, adequate support for machine.

1.Remove the Blade Drive Belt (Steps 1-10: Blade Drive Belt Replacement Procedure).

2.Assure that spark plug wire is disconnected.

3.Support rear of unit to allow access to underside of the machine near the rear.

Note: Unit is heavy. Be sure support is adequate to prevent personal injury.

4.Observe the belt fingers Item 63), position of idler and belt routing.

5.Remove the belt finger retaining nuts and bolts (Items

126and 143).

6.Move the belt finger and remove the belt from the transaxle pulley (Item 48).

7.Remove the belt from the drive idler (Item 105).

8.Remove the belt from the engine drive pulley (Item

85).

9.Install new belt on the top (small) engine pulley, drive idler and transaxle pulley using the original belt position and routing.

10.Reposition and secure the belt finger using the original bolts, washers and nuts.

NOTE: Before installing the fasteners inspect them for wear and replace as necessary.

11.Reinstall the Blade Drive Belt (Steps 11-16: Blade Drive Belt Replacement Procedure).

Note: With clutch levers engaged, be sure belt guides do not touch belts after installation.

12.Replace the cover

13.Reconnect spark plug wire.

14.Start engine and check both belts for proper operation of blade drive system and mower drive system.

WARNING: If the drive clutch begins to squeal or slip, do not continue to operate your unit until adequate adjustment or repair has been performed. Improper adjustment can cause drive clutch to slip and overheat, greatly reducing machine performance and transmission

life.

Part No. 520166

Page 13 of 20

Form No. F112003A

Image 13
Contents Accessories 8VIBRATION 7SOUNDGeneral Safety Assembly Controls Literature AssyPatent Pending Cutting Operation StartingBlade Clutch Cutting Height AdjustmentHandling & Transporting PropulsionStorage Maintenance Starter Switch Wiring Cable AdjustmentsBlade Removal / Sharpening Belt ReplacementSpindle Drive Belt Brake Puck Replacement Parts Drawing FM3300INB, FM3300INEB Deck AssemblyFM3300INB, FM3300INEB Engine AssemblyParts Drawing Drive AssemblyFM3300INB, FM3300INEB Handle Assembly Transaxle Guard KIT Grass Catcher KITProblem Possible Cause Solution Troubleshooting