Billy Goat TKD502SP specifications CE95

19					Item			Description	TKD502SP	Qty.
					No.				Part No.
		Parts List		86			WHEEL WITH SPROCKET ASS’Y CAST (21, 36, 94, 95, 96)		890242	2
				87			CHAIN 52 PITCH		890239	2
		continued from	88				CHAIN 40 PITCH		900323	1
		page 11.		89			WASHER FLAT 5/16 (3/8 ID x 7/8 x 1/16)		*8171003	4
				90			BOLT CARRIAGE 5/16 -18 x 3/4		*8024039	4
			91				WASHER SPRING LOCK 5/16		*8177011	4	* Denotes
				92			NUT REGULAR 5/16-18		*8142002	5	standard
				93			JACKSHAFT		900320	1	hardware item
				94			SPROCKET (PER ASSEMBLY) (SIZE # 65A26) 26 TEETH		890238	1	that may be
				95			SCREW SELF TAP 1/4-14 x 3/4 (PER ASSEMBLY)		800505	5
											purchased
				96			WASHER LOCK EXTERNAL TOOTH (PER ASSEMBLY)		*8181007	5
											locally.
			97				JACKSHAFT ASS’Y (INCLUDE. 93, 101, 102, 107, 108, 109)		890197	1
				98			SHIELD MUFFLER TKDSP		890190	1	Denotes
			99				LABEL CLUTCH		900328	1
											parts found
					100		LABEL-WARNING GUARDS		900327	1
				101			BEARING PLATE		900317	2	in parts bag
				102			BEARING BALL (WITH SNAP RING)		900321	2	assembly.
			103				WASHER LOCK 1/4		*8177010	2
				104			ROD BAIL CLUTCH ASS’Y (INCLUDE. GRIP)		900969	1
				105			BAR BRACE HANDLE		900768	1
				106			SCREW CAP 5/16-18 x 3/4		*8041026	1
				107			SPROCKET - 17 TOOTH		900303	1
			108				SPROCKET - 8 TOOTH		900302	2
				109			ROLL PIN 3/16 DIA. x 1 1/4 LG.		*8195166	4
				110			LOCKNUT 5/16 - 18 FLANGE		850164	5
				111			SCREW CAP 1/4 - 20 x 1 1/4		*8041007	1
			112				BRACKET CONTROL ASS’Y (INCL. 113, 114, 115)		900221	1
				113			SPRING		900136	1
			114				ROLL PIN 1/8” DIA. x 1 1/4 LG.		*9195106	1
				115			ROD CLUTCH		900208	1
				116			SCREW CAP 1/4-20 x 1” LG.		*8041006	2
				117			WASHER 1/4” FLAT (5/16 ID x 3/4 OD x 1/16)		*8171002	6
				118			GUARD CHAIN ASS’Y TKDSP		890195	1
				119			CLIP-CLUTCH CABLE		900999	1
			120				PLATE BRACE HT. ADJ. KD / TKD		900756	1
				121			CLUTCH DOUBLE RELEASE		900307	1
				122			WASHER FENDER 5/16		*8172020	1
			123				LABEL READ OWNER'S MANUAL		890301	1
20		TROUBLESHOOTING						Before Requesting Service Review These Suggestions
		Problem						Possible Cause			Solution
	Will not vacuum or has poor					Dirty debris bag. Nozzle height set too high or too low. Hose kit cap			Clean debris bag.		Shake bag clean or wash. Adjust nozzle height.
	vacuum performance.						missing. Clogged nozzle or exhaust. Excessive quantity of debris.		Checkfor hose kit cap. Unclog nozzle or exhaust (see page 5).
									Allow air to feed with debris.
	Poor chipping performance.					Extremely hard wood.		Dull or damaged chipper blade.	Avoid extremely hard wood. Sharpen or replace chipper blade (see
									page 8).
	Engine stalls or labors when					Feeding branches into chipper too rapidly. Engine service may be			Feed branches at a slowerrate. Service engine.
	chipping.						required.
	Abnormal vibration.						Loose or out of balance impeller or loose engine.		Check impeller and replace if required. Check Engine.
	Engine will not start.						Throttle in off position.	Out of gasoline. Bad or old gasoline.	Check stop switches,throttle, and gasoline.Connect spark plug wire.
							Spark Plug wire disconnected. Dirty air cleaner.		Clean or replace air cleaner.Or contact a qualified service person.
	No self propelling.						Operator's bail not releasing clutch. Broken or out of adjustment		Adjust clutch cable. Adjust bracket control assembly. Replace any
							clutch cable.W orn or broken clutch assembly. Bracket control		worn or damaged or malfunctioning parts.
							assembly (item 112) out of adjustment.
	Self propelled drive will not						Clutch cable out of adjustment. Clutch not lubricated and is locked-		Adjust clutch cable. See page 9 Clutch Adjustment. Oil clutch.
	release.						up.
	Engine is locked, will not						Debrislocked in chipper blade, hopper or inside impeller. Engine		See page 5,	Clearing a clogged chipper hopper. Contact an engine
	pull over.						problem.		servicing dealer for engine problems.

10

LIST

22.1	Engine Service and Warranty
	Contact your nearest engine manufacturer's authorized
		servicing dealer.
21	Serial Plate	Record your machine model, serial number and
		date-of-purchase and where purchased

WARRANTY PROCEDURE

22Please fill in the WARRANTY CARD and send the upper part to Billy Goat. The WARRANTY terms are stated on the lower part which remains with the user. Whenever a Billy Goat Machine is faulty due to a defect in material and / or workmanship, the owner should make a warranty claim as follows:

The Machine should be taken to the dealer from whom it was purchased or to an authorized Billy Goat dealer.

	PA RTS
	12
SHOOTING, &	PROCEDURE

L A

97

LpA

109

Operator

		CE95
1803 S. Jefferson P.O. Box 308
Lee's Summit, Mo.	64063 / USA
(816) 524-9666 FAX (816) 524-6983
Model		Serial	No.
Unit (weight)		Engine Power
lbs	kg	kW		min-1
		@

The owner should present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.

The Warranty Claim will be filled in by the authorized Billy Goat Dealer, who will send it with the faulty part to Billy Goat headquarters.

The Quality / Service department at Billy Goat headquarters will study the claim and parts and will notify their conclusions.

The decision by the Quality / Service department at Billy Goat headquarters to approve or reject a Warranty claim is final and binding.

Note: To process a Warranty Claim, it is necessary to quote the Model & Serial number who are printed on the Billy Goat Serial Plate.

TROUBLE W ARRANTY

Purchase	Purchased
Date	from
Part No. 890207

BILLY GOAT INDUSTRIES INC.

P.O. BOX 308 (1803 S JEFFERSON LEE'S SUMMIT, MO. 64063 / USA

PHONE: 816-524-9666 FAX: 816-524-6983

Page 12 of 12 Form No. F021795E