MULTI-PURPOSE WORK BENCH ASSEMBLY INSTRUCTIONS
#92558
| DESCRIPTION | ORDER PART # | QTY |
|
|
|
|
A | M10 X 55MM BOLT |
| 3 |
|
|
|
|
B | M6 X 50MM BOLT |
| 6 |
|
|
|
|
C | M6 X 16MM BOLT |
| 16 |
|
|
|
|
D | M6 NUT |
| 12 |
|
|
|
|
E | 6MM WASHER |
| 6 |
|
|
|
|
F | 10MM WASHER |
| 5 |
|
|
|
|
G | 12MM WASHER |
| 4 |
|
|
|
|
H | 10MM END CLIP |
| 2 |
|
|
|
|
I | 12MM END CLIP |
| 4 |
|
|
|
|
J | 10MM PVC COVER |
| 2 |
|
|
|
|
K | 12MM PVC COVER |
| 2 |
|
|
|
|
L | M6 PVC NUT COVER |
| 4 |
|
|
|
|
M | WHEEL AXLE | WB0001 | 1 |
|
|
|
|
|
|
|
|
DESCRIPTION ORDER PART #QTY
N | LARGE WHEEL | WB0002 | 2 |
|
|
|
|
O | WHEEL COVER | WB0003 | 4 |
|
|
|
|
P | AXLE SLEEVE | WB0004 | 3 |
|
|
|
|
Q | RIGHT SUPPORT | WB0005 | 1 |
| FRAME |
|
|
R | LEFT SUPPORT | WB0006 | 1 |
| FRAME |
|
|
S | CUSHION | WB0007 | 1 |
| HANDLE GRIP |
|
|
T | CASTERS | WB0008 | 2 |
|
|
|
|
U | FRONT SUPPORT | WB0009 | 1 |
| BAR |
|
|
V | REAR SUPPORT | WB0010 | 1 |
| BAR |
|
|
W MIDDLE SUPPORT | WB0011 | 1 | |
| FRAME |
|
|
X | FRONT PANEL | WB0012 | 1 |
|
|
|
|
Y | COILED SHELF | WB0013 | 1 |
|
|
|
|
Z | SINK TOP BASIN | WB0014 | 1 |
DESCRIPTION ORDER PART #QTY
AA | DRAIN PLUG | WB0015 | 1 | |
BB | DOWEL RODS | WB0016 | 3 | |
|
|
|
| |
CC | REAR FAUCET | WB0017 | 1 | |
PANEL | ||||
|
|
| ||
DD | FOLDING | WB0018 | 1 | |
COUNTER | ||||
|
|
| ||
| AXLE FOR |
| 1 | |
EE FOLDING COUNTER | WB0019 | |||
FF | DRAWER | WB0020 | 1 | |
|
|
|
| |
GG | BOTTOM TRAY | WB0021 | 2 | |
|
|
|
| |
HH | “S” HOOKS | WB0022 | 6 | |
|
|
|
| |
I I | FAUCET | WB0023 | 1 | |
|
|
|
| |
JJ | FOLDING COUNTER | WB0024 | 2 | |
HINGE | ||||
TOOLS REQUIRED FOR ASSEMBLY
Hex Wrench
Hex Bolt Driver
STEP 1
identify all parts packed in carton against the parts list. Remove all protective materials. Place parts on a
Read entire assembly instructions before beginning assembly.
STEP 2 WHEEL ASSEMBLY
Insert wheel axle (M) through bottom shaft of right side support frame
(Q).so that it is centered inside the shaft with equal amount of axle on each side. Snap 12mm end clip (I) on notch in axle closest to the right side support frame (Q). Add the following parts to the axle in this order: 12mm washer (G), wheel cover (O), axle sleeve (P), wheel (N), wheel cover (O), 12mm washer (Q), 12mm end clip (I) as shown in figure 1. Be sure the wheel is inserted over the axle sleeve in a manner that allows it to rotate freely. Secure the wheel assembly on the axle with the 12mm washer clip (I). Repeat procedure for opposite side wheel.
STEP 3 LEFT SIDE SUPPORT FRAME ASSEMBLY
Screw in the two casters (T) into the bottom of the left side support frame (R) as shown in figure 2. Add the cushion handle grip (S) to the left side support frame
(R)as shown in figure 2. Insert two M6 x 50mm bolts (B) through end of cushion grip handle and through the holes in the left side support frame. Add a 6mm washer (E), 6mm nut (D). Tighten with wrench. Do not over tighten. Add M6 PVC cover to the end of each nut. Repeat on opposite side of cushion grip handle.
Figure 1
Figure 2
PAGE 1