Exmark PHZ19KA343CA manual Specifications, Model Numbers, Systems

Page 13

Specifications

Specifications

Model Numbers

Serial Nos: 790,000 and Higher

PHZ19KA343; PHZ19KA343CA

Systems

Engine

•Engine Specifications: See your Engine Owner’s Manual

•RPM: Full Speed: 3750 ±100 RPM (No Load)

Idle: 1400 RPM

Fuel System

•Capacity: 7.7 gal. (29.1 L)

•Type of Fuel: Regular unleaded gasoline, 87 octane or higher.

•Fuel Filter: In-line Kawasaki P/N 49019–7001

•Fuel Shut-Off Valve: 1/4 turn increments (“ON”, “OFF”)

Electrical System

•Charging System: Flywheel Alternator

•Charging Capacity: 13 amps

•Battery Type: BCI Group U1

•Battery Voltage: 12 Volt

•Polarity: Negative Ground

•Fuses: Two 20 amp blade type

Safety Interlock System

•PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

•Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

•Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

•Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

–Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

–Steering is controlled by varying the position of the levers relative to each other.

–Moving motion control levers outward (in slots) locks the drive system in neutral.

•PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

•Parking Brake Lever: Engages parking brake.

•Deck Height Adjustment Lever: Sets cutting height to desired position.

•Deck Lift Assist Lever: Foot pedal that assists in raising the deck.

Seat

•Type: Standard seat with high back, foam padded, (internal suspension) and armrests.

•Mounting: Hinged to tilt up for access to battery and other components. Held in tilted position with lanyard. Adjustable fore and aft seat track.

•Armrests: Standard–foam padded flip-up armrests.

•Seat Safety Switch: Incorporated into the Safety Interlock System. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

•Hydrostatic Drive: Two Hydro Gear ZT2800 Integrated drive systems.

•Hydraulic Oil Type: Use Exmark Premium Hydro Oil.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Phazer California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals Safety 109-2494 Model Numbers SpecificationsSystems Dimensions Torque Requirements Product OverviewControls OperationOperating Instructions Pre-StartStopping the Engine Disengaging the PTODriving the Machine Transporting Adjusting the Cutting HeightTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check for Loose Hardware Check Safety Interlock SystemChange Engine Oil Service Air CleanerCheck Hydraulic Oil Level Check Tire PressuresLubricate Caster Wheel Hubs Lubricate Grease FittingsChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter Thread Locking Adhesives Fuel Tank Mounting Hardware SpecificationsMobil HTS Grease Or Food-Grade Anti-seize Dielectric GreaseMotion Control Linkage Adjustment Electric Clutch AdjustmentDeck Leveling Pump Drive Belt TensionClean Engine Air Cooling System Adjust Throttle Lever TensionRemove Engine Shrouds and Clean Cooling Fins Clean Grass Build-Up Under DeckWaste Disposal Battery DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsTAN Black Blue .LT Electrical Logic SchematicExmark Commercial Turf Equipment Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options
Top Page Image Contents