and then back between the stack pulley and the steering plate (3).
10.Remove the motion drive belt. A correct re- placement part or assistance is available from an Authorized Service Centre in your area.
11.To install the motion drive belt, reverse the above steps.
12.(Figure 23) Check the routing of the motion drive belt (1). Make sure the motion drive belt is installed correctly on the idler pulleys
(2).
How To Replace The Mower Drive Belts (Figure 13)
1.Remove the mower housing. See the instruc- tions on ªHow To Remove The Mower Hous- ingº.
2.Loosen and pull the belt retainer (1) away from the double idler pulley (2). Remove the primary mower drive belt (3) from the double idler pulley (2).
3.Pull the belt retainers (4) away from the single idler pulley (5). Remove the primary mower drive belt (3) from the single idler pulley (5).
4.Remove the primary mower drive belt (3) from the mower housing.
5.To release tension on the secondary belt, remove the spring (8) from the double idler mount (9).
6.Remove the secondary mower drive belt (10) from the double idler pulley (2) and from the right mandrel pulley (11).
7.A correct replacement part or assistance is available from an Authorized Service Centre in your area.
8.To install the mower drive belt, reverse the above steps.
How To Remove The Mower Housing (Figure 38)
1.Move the blade rotation control (1) to the
DISENGAGE position.
2.Move the lift lever (2) to the level adjust- ment position.
3.Remove the hair pins and the washers from the adjuster arms (3). See illustrations ªCº and ªDº.
4.Remove the hair pins and washers from the suspension links (4). See illustrations ªAº and ªBº.
5.Disconnect the extension spring (5) from the blade control rod (6). See illustration ªEº.
6.Disconnect the front hanger (9) from the axle support. See illustration ªFº.
NOTE: The hanger rod (11) is made with a bend.
7.Remove the mower drive belt (7) from the stack pulley (8). See illustration ªGº.
8.Disconnect the middle discharge chute
(10) from the mower housing. See illustration ªHº.
9.Pull the mower housing away from the right side of the unit.
10.To install the mower housing, reverse the above steps.
11.Check belt routing of the primary mower drive belt (1) and the secondary mower drive belt (2). See illustration ªJº.
How To Replace The Fuse
If the fuse is blown, the engine will not start. Remove the fuse and replace with a 15 amp. automotive fuse.
Storage (over 30 days)
At the end of each year, prepare the unit for storage as follows.
1.Drain the fuel from the carburettor and the fuel tank. Change the engine oil. See the en- gine manufacturer's instructions.
2.Clean the entire unit.
3.Charge the battery.
GB
WARNING: Never store the grass bagger with grass clippings in the bags. Even a small amount of
grass or debris can generate enough heat to start a fire.
WARNING: Do not operate unless the entire grass bagger attachment is in place.
How To Order Replacement Parts
Use only manufacturer's authorized or approved replacement parts. The letter placed on the end of the part number denotes the type of finish for the part, C for chrome, Z for zinc, a PA for purchased assembly. It is important that you include this when ordering a part. Do not use attachments or accessories not specifically recommended for this unit. In order to obtain proper replacement parts you must supply the model number of your mower (see nameplate).
Replacement parts, except for the engine, trans- mission, transaxle or differential, are available from the store where the mower was purchased or a service shop recommended by the store.
If you are unable to obtain parts or service in the manner outlined above, then contact:
HAYTER LIMITED, Service Department, Spell- brook, Bishop's Stortford, Hertfordshire. CM23 4BU.
UK ONLY: Details of your local Hayter authorised dealer are contained in Yellow Pages or contact: Freephone 0800 616298.
Replacement parts for the engine, transaxle, or transmission, are available from the manufactur- er's authorized service centre found in the com- mercial pages of the telephone directory. Also, see the individual engine or transmission warranties to order replacement parts.
When ordering the following information is required:
(1)The Model Number
(2)Serial Number
(3)Part Number
(4)Quantity
F±000794J | 19 |