Husqvarna LE475 manual Correct Edger-Trimmer Usage, Operation Of The Edger Trimmer

Page 8
CORRECT EDGER-TRIMMER USAGE

CORRECT EDGER-TRIMMER USAGE

OPERATION OF THE EDGER-CAUTION This equipment does not include a spark arrestor mu￿er. Readallmanualsprovidedbeforeoperating. These manuals give a detailed description of operation and point out other areas of caution. Familiarize yourself thoroughly with equipment before attempting to use it.

OPERATION OF THE EDGER-

TRIMMER

Manual backgroundWARNING Manual background Keep all shields in place. Never at- tempt to clear discharge areas or edger- trimmer blade wihout disengaging the edger-trimmer and stopping the engine.

Your edger-trimmer is designed to give a professionally groomed appearance to your lawn with minimum e￿ort. It will edge lawns at walks, around ￿ower beds, trim close to poles and hydrants, and also under fences and other hard to reach locations. For best appearance around ￿owers, adjust blade to 20" angle cut.

For best results, adjust the cutting depth of the blade to within 1/2" to 1" deep (with a new blade usually in the third notch of the adjustment bracket at handle).

Too deep a cut will put unnecessary stress on engine and accelerate blade wear. Cutting too shallow allows rapid regrowth of roots.

Make sure to re-adjust cutting depth as blade begins to wear at tips.

Avoid edging or trimming in wet grass, as it may clog up in the blade guard and cause splattering. The general appearance will be much better when grass is dry.

Always push edger-trimmer at moderate walking speed — at this speed your edger-trimmer is designed to cut more than 100 ft. per minute. Four-wheel design of edger-trimmer permits easy and stable edging, riding securely on sidewalk or cement surfaces.

Around specially shaped ￿ower beds or curved sections, follow these simple steps. It will be easier to cut around corners when front wheels are placed together at right side of trimmer-edger. Before starting engine, remove wheel spacer clip on front axle, slide wheels to side away from blade, and replace spacer.

After starting engine, set blade depth and by slightly lifting rear wheels, guide edger-trimmer around corners and odd angles.

WARNING TO PURCHASERS OF Manual background INTERNAL COMBUSTION ENGINE EQUIPPED MACHINERY OR DEVICES

This equipment does not include a spark arrestor mu￿er.

If this equipment is used on any forest-covered land, brush-covered land, or grass-covered land in the State of California, the law requires that

aspark arrestor be installed and in e￿ective working order before using this equipment on such land. The spark arrestor must be attached to the exhaust system and comply with Section 4442 of the California Public Resources Code.

If this equipment is used in a state or national park or campground, a U.S.D.A. Forestry Department approved spark arrestor mu￿er must be utilized.

8

Image 8
Contents WITH PARTS LIST Maintenance InformationSpecications Operating InstructionsTABLE OF CONTENTS AVOIDINJUR Y Thissymbolmarksimportantinstructionsrelatingtoyourpersonalsafety.ToGENERAL SAFETY SUGGESTIONS MAINTENANCE AND STORAGETRAINING PREPARATIONEDGER-TRIMMER FEATURES ASSEMBLY INSTALLING THE THROTTLE WIREFUEL SPECIFICATION ATTACHING THE HANDLECLUTCH AND DEPTH LEVER SETTINGS See Fig ADJUSTING CUTTERHEAD ANGLE See FigWARNING Never adjust cutterhead angle when engine is running OPERATING YOUR EDGER-TRIMMEROPERATING YOUR EDGER-TRIMMER, CONT WHEEL POSITIONING See FigCURB RIDING POSITION WARNING Do not change wheel positions when engine is runningThis equipment does not include a spark arrestor muer CORRECT EDGER-TRIMMER USAGEOPERATION OF THE EDGER TRIMMER MAINTENANCE CHECKLIST BLADE MAINTENANCEMAINTAINING YOUR EDGER-TRIMMER SPARK PLUGLAWN EDGER AND TRIMMER PARTS ILLUSTRATION 505289937 LAWN EDGER AND TRIMMER PARTS LISTEngine Pulley TROUBLESHOOTING CHART P R O B L E MC A US E 1. Engine fails to startMAINTENANCE NOTES STORAGE INSTRUCTIONSMAINTENANCE NOTES MAINTENANCE NOTES WARRANTY STATEMENT SECTION 1 LIMITED WARRANTYSECTION 2 HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY SECTION 6 PROCEDURE TO OBTAIN WARRANTY CONSIDERATION