Husqvarna YTH21K46 To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch.

TO STOP MOWER BLADES - disengage attachment clutch control.

S

FIG. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH21K46 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningSpark Plugs Deck Washout Port See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Schematic Tractor - Model Number YTH21K46 96045002100, Product no 45Electrical KEY Part Description Chassis Tractor - Model Number YTH21K46 96045002100, Product no 45 Drive Washer Harden .793 x 1.637 x 30!2+ª!22%34%2ª+4 EngineEngine Kohler Model No. SV610-0212 Steering Assembly Tractor - Model Number YTH21K46 96045002100, Product no 45 Mower Deck KEY Part NO. no Description Mower Lift 8787 100 101Seat Assembly 532 42 SeatDecals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX08.18.09 CL

96045002100, YTH21K46 specifications

The Husqvarna YTH21K46 is a robust and efficient riding mower, designed for homeowners who demand reliability, performance, and ease of use in maintaining their lawns. Powered by a strong 21.5 HP Kohler engine, this riding mower provides ample power to tackle various mowing conditions while ensuring durability and long-lasting performance.

One of the standout features of the YTH21K46 is its 46-inch cutting deck. This deck allows for efficient mowing of medium to large-sized lawns, covering more ground in fewer passes. The cutting height can be easily adjusted via a rugged lever, offering six different positions ranging from 1 to 4 inches. This versatility enables users to achieve the desired lawn appearance while accommodating different grass types and seasonal conditions.

An important technological feature included in this model is the ReadyStart system, which allows for easy engine start-up without the need to prime, enhancing user convenience. This, combined with the smooth hydrostatic transmission, provides seamless acceleration and deceleration, making it simple to navigate around obstacles and tight spaces. The steering wheel is ergonomically designed, ensuring comfort and ease of control during operation.

The Husqvarna YTH21K46 also boasts a comfortable and spacious operator's platform, which includes an adjustable seat to accommodate different user heights, promoting an enjoyable mowing experience. The optimized design creates an ideal driving position, reducing fatigue during extended use. Moreover, a front-mounted bumper adds protection and enhances the thermal efficiency of the mower.

In addition to its cutting capabilities, this riding mower is designed with functionality in mind. The integrated LED headlights improve visibility during early morning or late evening mowing sessions. A washout port makes it easy to clean the cutting deck, ensuring optimal performance and longevity.

Lastly, the YTH21K46 supports various attachments and accessories, including mulching kits, baggers, and snow blades, expanding its versatility for year-round lawn care. This adaptability means it's not just a seasonal mower; it serves as a multifunctional tool to help maintain your property in every season.

With its blend of powerful performance, user-friendly design, and smart technologies, the Husqvarna YTH21K46 provides homeowners a reliable solution for achieving a well-manicured lawn.
Top Page Image Contents