Husqvarna 353 EPA III, 1151435-95 manual Fuel Handling

Page 18

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

 

WARNING! Always ensure there is

 

 

adequate ventilation when handling fuel.

 

 

 

 

 

 

 

Gasoline

Use good quality unleaded gasoline.

CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures. Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws fitted with catalytic converters means that only unleaded gasoline can be used.

The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the first 10 hours.

Two-stroke oil

For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre

Two-stroke oil, litre

 

 

 

2% (1:50)

 

 

5

0,10

 

 

10

0,43/0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

Mixing

Always mix the gasoline and oil in a clean container intended for fuel.

Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

Do not mix more than one month’s supply of fuel at a time.

If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

We recommend the use of special oil (chain oil) with good adhesion characteristics.

Never use waste oil. This results in damage to the oil pump, the bar and the chain.

It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

18 – English

Image 18
Contents 346XP EPA I 353 EPA KEY to Symbols Symbols on the machineSymbols in the operator’s manual EPA Contents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment Assembly Fitting the bar and chainProtect your hands from injury Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springLubricating the bar tip sprocket Air filterSpark plug Needle bearing lubricationTemperature 0C 32F or colder Adjustment of the oil pumpAir Injection centrifugal cleaning Cooling systemHeated handles Electrical carburetor heating346XPG, 353G Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations 050058 Saw chain filing and file gauges Federal Emission Control Warranty Statement Repair or Replacement of Parts Repair orConsequential Damages Husqvarna Forest Kickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1151435-95

353 EPA III, 1151435-95 specifications

The Husqvarna 1151435-95,353 EPA III is a notable addition to the world of outdoor power equipment, catering specifically to those who demand efficiency, power, and sustainability. This quality product is designed for both homeowners and professionals, striking an impeccable balance between high performance and user-friendly operation.

One of the standout features of the Husqvarna 1151435-95,353 EPA III is its cutting-edge 2-stroke engine technology. With a focus on reducing emissions, this engine complies with the stringent EPA III regulations, making it an environmentally responsible choice. It utilizes advanced combustion processes that not only enhance fuel efficiency but also minimize harmful exhaust pollutants, ensuring a cleaner atmosphere while delivering the power needed for demanding tasks.

Another remarkable characteristic of this model is its ergonomic design. The machine is built for comfort during prolonged use, featuring an adjustable handle, anti-vibration technology, and a lightweight structure that significantly reduces user fatigue. These ergonomics allow for better control and maneuverability, ensuring users can navigate varied terrains with ease.

The Husqvarna 1151435-95,353 EPA III also comes equipped with Smart Start technology, which simplifies the starting process. This feature minimizes resistance in the starter cord, making it easier to start the machine with minimal effort. This is especially beneficial for those who might struggle with traditional starting systems.

Additionally, this model showcases a well-designed cutting system. Its sharp, durable blades provide precision cutting, whether you're tackling thick grass or dense brush. The adjustable cutting height allows for customized performance to suit different types of landscaping needs, making it versatile in various scenarios.

Durability is another hallmark of the Husqvarna 1151435-95,353 EPA III. Constructed with high-quality materials, this machine is designed to withstand the rigors of outdoor work. Its robust build quality ensures longevity, reducing the need for frequent repairs or replacements.

Overall, the Husqvarna 1151435-95,353 EPA III represents a significant step in modern outdoor equipment. With its environmentally friendly engine, ergonomic design, easy starting capabilities, and robust cutting performance, it is well-suited for both professional landscapers and avid gardeners alike. This model epitomizes Husqvarna's commitment to innovation and quality, making it a reliable choice for anyone in need of efficient outdoor power tools.