Husqvarna 1151435-95, 353 EPA III manual Limbing

Page 25

WORKING TECHNIQUES

5Do the conditions and surrounding terrain affect how safely you can stand and move about?

Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting.

IMPORTANT! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw.

The following instructions describe how to handle the common situations you are likely to encounter when using a chain saw.

Limbing

When limbing thick branches you should use the same approach as for cutting.

Cut difficult branches piece by piece.

12

3

Cutting

WARNING! Never attempt to cut logs ! while they are in a pile or when a couple

of logs are lying together. Such procedures drastically increase the risk of kickback which can result in a serious or fatal injury.

If you have a pile of logs, each log you attempt to cut should be removed from the pile, placed on a saw horse or runners and cut individually.

Remove the cut pieces from the cutting area. By leaving them in the cutting area, you increase the risk for inadvertently getting a kickback, as well as increasing the risk of losing your balance while working.

The log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there is a risk that the chain will touch the ground when you finish the cut.

Cut all the way through the log from above. Avoid letting the chain touch the ground as you finish the cut. Maintain full throttle but be prepared for what might happen.

If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log.

Turn the log and finish the cut from the opposite side.

The log is supported at one end. There is a high risk that it will split.

Start by cutting from below (about 1/3 of the way through).

Finish by cutting from above so that the two cuts meet.

The log is supported at both ends. There is a high risk that the chain will jam.

English – 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 346XP EPA I 353 EPA Symbols on the machine KEY to SymbolsSymbols in the operator’s manual EPA Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Cutting equipment Stop switchVibration damping system MufflerBar Cutting equipment designed to reduce kickbackChain Injuries Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Which could lead to serious, even fatal injuries Chain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyProtect your hands from injury Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Terms Basic cutting techniqueLimbing Safe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Directional cutsFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral High speed jet H Correctly adjusted carburetorChecking brake band wear Checking the front hand guardImmediately Checking the inertia brake releaseMuffler Changing a broken or worn starter cord StarterTensioning the recoil spring Changing a broken recoil springSpark plug Air filterLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Adjustment of the oil pumpTemperature 0C 32F or colder Cooling systemElectrical carburetor heating Heated handles346XPG, 353G Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data050 Bar and chain combinations058 Saw chain filing and file gauges Repair or Replacement of Parts Repair or Federal Emission Control Warranty StatementConsequential Damages Husqvarna Forest Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautions1151435-95

353 EPA III, 1151435-95 specifications

The Husqvarna 1151435-95,353 EPA III is a notable addition to the world of outdoor power equipment, catering specifically to those who demand efficiency, power, and sustainability. This quality product is designed for both homeowners and professionals, striking an impeccable balance between high performance and user-friendly operation.

One of the standout features of the Husqvarna 1151435-95,353 EPA III is its cutting-edge 2-stroke engine technology. With a focus on reducing emissions, this engine complies with the stringent EPA III regulations, making it an environmentally responsible choice. It utilizes advanced combustion processes that not only enhance fuel efficiency but also minimize harmful exhaust pollutants, ensuring a cleaner atmosphere while delivering the power needed for demanding tasks.

Another remarkable characteristic of this model is its ergonomic design. The machine is built for comfort during prolonged use, featuring an adjustable handle, anti-vibration technology, and a lightweight structure that significantly reduces user fatigue. These ergonomics allow for better control and maneuverability, ensuring users can navigate varied terrains with ease.

The Husqvarna 1151435-95,353 EPA III also comes equipped with Smart Start technology, which simplifies the starting process. This feature minimizes resistance in the starter cord, making it easier to start the machine with minimal effort. This is especially beneficial for those who might struggle with traditional starting systems.

Additionally, this model showcases a well-designed cutting system. Its sharp, durable blades provide precision cutting, whether you're tackling thick grass or dense brush. The adjustable cutting height allows for customized performance to suit different types of landscaping needs, making it versatile in various scenarios.

Durability is another hallmark of the Husqvarna 1151435-95,353 EPA III. Constructed with high-quality materials, this machine is designed to withstand the rigors of outdoor work. Its robust build quality ensures longevity, reducing the need for frequent repairs or replacements.

Overall, the Husqvarna 1151435-95,353 EPA III represents a significant step in modern outdoor equipment. With its environmentally friendly engine, ergonomic design, easy starting capabilities, and robust cutting performance, it is well-suited for both professional landscapers and avid gardeners alike. This model epitomizes Husqvarna's commitment to innovation and quality, making it a reliable choice for anyone in need of efficient outdoor power tools.
Top Page Image Contents