ENGLISH
OPERATIONS
1.MEMORY PRESETTING a. Manual operation
For example: presetting FM 90.1 M Hz, to Preset number. 10
1.Select the FM by using the BAND button.
2. Tune to 90.1 MHz by using the TUNING 5∞ button.
3.Press the MEMO button briefly (for less than 0.5 second) Then, “MEMO” will bricking in the florescent tube display.
4. Select the preset number by using the TUNING 5∞ button.
5.MEMO button pushed again, 90.1 MHz (broadcast station) was able to be memorized in number 10 by this.
Note:
Be sure to select the antenna A or B memorization when you preset manual memory in FM broadcast.
b. Automatic operation
1.Select the desired broadcasting (FM or AM) by using the BAND but- ton.
2.Press the MEMO button slightly longer than 1.5 second does. Then, broadcasting will be automatically received, and as many broadcasting station are received well will be memorized preset num-
3. Check the broadcasting station by using the TUNING 5∞ button.
Note:
1.In the case of FM automatic presetting, the antenna A, B selector is set to “A” automatically,
And the broadcasting station is scanned twice. The stations that have stronger broadcasting signal are preset in the first time.; weaker ones are preset in the second time.
2.If a new broadcasting station is preset into a channel the broad- casting station which has been preset into that position aria will be automatically erased.
3.In mountainous or remote area broadcasting stations which have weak broadcasting signals cannot be automatically preset into the memory.
4.Max. 30 broadcasting stations each for FM, AM bands can be preset.
2.LISTENING TO RADIO
1.Select FM or AM by using the BAND button.
2.Tune to the desired broadcast by using the TUNING or PRESET 5∞ button.
3.FM broadcasting is set up to “STEREO” mode
If the broadcasting signal is weak, or if there is a large amount of interference in FM stereo broadcast, change the monaural mode by presetting the FM MODE button.
4.Select the IF BAND (FM bandwidth)
Select the NARROW bandwidth by pressing this button if the broad- cast signal is interfered with adjacent broadcast in the FM .
3. FINE, MANUAL TUNING
This function used for selection the manual tuning of the fine tuning mode.
Fine tuning mode is available only in the FM mode.
1.Press the TUNING MODE button.
2.Every time you press this button, the following will be displayed
FINE ⇔ MANUAL.
a. In FINE (Tuning) mode
When you try press the TUNING 5∞ button, the frequency will be se- lected by 10 kHz step to ± 50 kHz. Then, it will automatically be set to the MANUAL mode in 4 second.
b. In MANUAL (Tuning) mode
1.Press the TUNING 5∞ button in the FM band, then the frequency will be selected by 50 kHz step.
2.In the MW band, the frequency will be selected by 10 kHz step.
4. DIRECT TUNING
1.Press the F. DIRECT (frequency direct) button
2.Next press the numeric (0 to9) button. For example: FM 98.10 MHz
a.FM is chosen with BAND (or TUNER) button on remote controller.
b.Press the F. DIRECT (Frequency Direct) button.
c.Press the numeric button of “9”.
d.Press the numeric button of “8”.
e.Press the numeric button of “1”.
f.Press the numeric button of “0”.
g.The display fixed 98.10 MHz and broadcast station received. MW, LW band is same as above operations.
5. ADJUSTING CURRENT TIME
You can adjust the current time regardless of power on/standby.
1.Press the TIME ADJ button. Then “Hour display” indicator will blink.
blink
2. The hour is set with the TUNING 5∞ button.
3.Press the NEXT button. Then “minute display” indicator will blink.
blink
4. The minute is set with the TUNING 5∞ button.
blink
5.Press the NEXT button.
2