Husqvarna 966614701, 966614401, 966553901, PZ34FX BF, PZ6034FX warranty Fuel Tank

Page 25

CONTROLS

Fuel Tank

IMPORTANT INFORMATION

It is recommended that fuel be added to both tanks on initial start up.

Read the safety instructions before refueling. The machine has two fuel tanks, one on each side just behind the seat. The capacity for each tank is 5.5 gallons (20.5 liters).

Regularly check the gas cap gasket for damage and keep the cap properly tightened.

The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel. Damage to the engine and components may occur.

When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to help insure good cold weather starting.

WARNING!

Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the Safety section).

WARNING!

The engine and the exhaust system become very hot during operation.

Risk for burns if touched.

Allow engine and exhaust system to cool before refueling.

WARNING!

Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

8065-007

Gasoline fuel tanks

IMPORTANT INFORMATION

Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.

25

Image 25
Contents Operator Manual All rights reserved Contents Page Introduction Manufacturing Number Good ServiceXxxx xxxxxx xxxxx xxxx Xxxxxx xxxxxxxxx. xx xxxxxxxx Symbols and DecalsRemove key before Performing any Safety Instructions SafetyGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentBe extra cautious when driving on slopes Safe Handling of Gasoline General Maintenance Risk of sparking Transport Spark Arrestors Rollover Protection System RopsControl Locations ControlsMotion Control Levers Parking Brake Blade SwitchThrottle Control Ignition Switch Fuses Choke Control Hour Meter Cutting Height Pedals Tracking KnobSeat should not be adjusted while unit is in motion Seat Adjustment LeverFuel Shut Off Valve Fuel Tank Training OperationSteering Before Starting Roll Bar and Safety BeltStarting the Engine Set the throttle Open the fuel tank valve Set the engine speed Jumper Cables Use Weak BatteryTo remove cables, reverse order Running Operating on Hills Mowing Tips Stopping the Engine Bypass Valves Moving Machine By HandMaintenance Maintenance For cleaning BatteryFor replacing Fuel Filter Safety SystemTire Pressures Parking brake adjustment Measure gap Deck Belt Deck Belt InstallationDeck Belt Removal Pump Belt Belt InstallationBelts Replacing Pump BeltCutting Blades Leveling Deck Adjusting the Mower DeckCaster Wheels Removal and InstallationAnti-scalp Rollers Deck Lift SpringUse protective glasses when cleaning and washing CleaningHardware Lubrication Schedule LubricationGeneral Cables Wheel and Deck ZerksFront Wheel Mount Front Wheel BearingsFluid and Filter Change Hydraulic DriveTransmission Purging Procedures Problem Cause TroubleshootingTroubleshooting Storage ServiceWinter Storage Wiring Diagram PZ6034FX Technical DataEngine TransmissionFrame DimensionStandard Hardware Torque SpecificationsMetric Standard Hardware USA requirements Conformity CertificatesDelivery Service Service JournalAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Service Journal Service Journal Page 115 461927 Rev a 2011-10-20