Husqvarna 6521CM To Stop Engine, To Start Engine, Mulching Mowing Tips, ADD Gasoline

OPERATION

•Change the oil after every 25 hours of operation or each season. You may need to change the oil more often un- der dusty, dirty conditions. See “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE

•Fill fuel tank to bottom of tank fi ller neck. Do not over- fi ll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel sys- tem of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO STOP ENGINE

•To stop engine, release operator presence control bar.

TO START ENGINE

NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal.

1.To start a cold engine, push primer three (3) times before trying to start. Use a fi rm push. This step is not usually necessary when starting an engine which has already run for a few minutes.

2.Hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back.

NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause

flooding and engine will not start. If you do fl ood engine, wait a few minutes before attempting to start and do not repeat priming steps.

8

MOWING TIPS

CAUTION: Do not use de-thatcher blade attachmentsonyourmower.Suchattach- ments are hazardous, will damage your mower and could void your warranty.

•Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings. It may also be necessary to reduce ground speed and/or run the lawn mower over the area a second time.

•For extremely heavy cutting, reduce the width of cut by overlapping previously cut path and mow slowly.

•For better grass bagging and most cutting conditions, the engine speed should be set in the FAST position.

•Pores in cloth grass catchers can become fi lled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catcher off with water and let dry before using.

•Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air fl ow and extend engine life.

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE “CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL.

•The special mulching blade will recut the grass clip- pings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biode- grade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades.

•Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight.

•For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. 9). If the lawn is over- grown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly.

MAX 1/3

FIG. 9

•Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the fi rst cut path.

•Change your cutting pattern from week to week. Mow North–South one week, then change to East–West the next week. This helps prevent matting/graining of lawn.