Husqvarna 560sr owner manual Assembly, HOW to SET UP Your Lawn Mower, To Unfold Handle see a & 1B

Page 4

ASSEMBLY

CAUTION: Do not operate this mower without the discharge guard or an entire approved grass catcher in place. These guards are for your protection and are required by the American National Standards Institute and Consumer Products Safety Commission.

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

HOW TO SET UP YOUR LAWN MOWER

TO UNFOLD HANDLE (SEE FIG. 1A & 1B)

IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS NOT TO PINCH OR DAMAGE CONTROL CABLES.

Raiselowerhandlesectiontooperatingpositionandsqueeze thebottomendsof lowerhandletowardseachotheruntilthe pin in handle can be inserted into one of the three height adjustment holes.

Remove protective padding , raise upper handle section to operating position and tighten handle knobs securely.

Remove any packing material from around control bar.

Your handles may be adjusted for your mowing comfort. Refer to Service and Adjustments section of this manual.

OPERATOR PRESENCE

CONTROL BAR

UPPER HANDLE

LIFT UP

 

OPERATING

LOWER POSITION HANDLE

FIG. 1

3-POSITION HANDLE

ADJUSTMENT

BRACKET

HANDLE PIN

FIG. 1B

TO INSTALL ATTACHMENTS (SEE FIG. 2)

Your lawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging:

Open rear door and remove mulcher plug. Store mulcher plug in a safe place.

You can now install catcher or optional clipping deflector.

To return to mulching operation, install mulcher plug into discharge opening of mower.

CAUTION: Do not run your lawn mower without mulcher plug in place or approved clippingdeflectororgrasscatcherinplace. Never attempt to operate the lawn mower with the rear door removed or propped open.

MULCHER PLUG

FIG. 2

ASSEMBLE GRASS CATCHER

IMPORTANT: YOUR LAWN MOWER IS MULCHER READY AND THE MULCHER PLATE MUST BE REMOVED BEFORE USING MOWERASABAGGER. TOCONVERTMOWERTOBAGGINGOR DISCHARGING,SEETHEOPERATIONSECTIONINTHISMANUAL.

TO ASSEMBLE & ATTACH GRASS CATCHER (See Fig. 3)

Put grass catcher frame into grass bag with rigid part of bag on the bottom.

Slip vinyl bindings over frame.

NOTE: If vinyl bindings are too stiff, hold them in warm water for a few minutes. If bag gets wet, let it dry before using.

Lift the rear door on the mower housing.

Place the grass catcher frame onto the formed tabs on the rear door hinge bracket.

The grass catcher is secured to the lawn mower housing when the rear door is lowered onto the grass catcher frame.

CATCHER

FRAME

 

VINYL

 

BINDINGS

 

RIGID BOTTOM

REAR

CATCHER

DOOR

FRAME

HINGE

BRACKET

TABS

FIG. 3

CAUTION: Do notrunlawn mowerwithout the discharge guard (rear door), approved grasscatcher,clippingdeflectorormulcher plate in place. Never attempt to operate mowerwiththedischargeguard(reardoor) removed or propped open.

4

Image 4
Contents 560sr Maintenance and Storage Safe Operation Practices for Walk-Behind MowersTraining PreparationTable of Contents Assembly HOW to SET UP Your Lawn MowerTo Install Attachments see FIG To Unfold Handle see a & 1BHOW to USE Your Lawn Mower OperationOperatorpresenceenginecontrolbar To Convert MowerGround Drive Three Speeds See a To Empty Grass Catcher See FigTo Operate Drive System See Figs a & 8B Before Starting Engine To Start EngineOIL See Fig GAS See FigMowing Tips Mulching Mowing TipsLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USELawn Mower Grass CatcherTires Blade CareCleaning EngineService and Adjustments To Adjust Cutting HeightTo Adjust Drive Control Cable Rear DeflectorTo Adjust Handle see FIG CarburetorEngine Speed Throttle ControlStorage OtherTroubleshooting Points Problem Cause CorrectionRepair Parts KEY Part Description Repair Parts Repair Parts KEY Part NO. no Description Service Notes Warranty Statement Limited Warranty