Husqvarna 5521 CHV 96143000106 manual To Replace Drive Belt See Fig, To Adjust Handle See Figs

Page 13

SERVICE AND ADJUSTMENTS

2.Remove belt from gearcase pulley.

3.Turn lawn mower on its side with air filter and carbu- retor down.

4.Remove blade, engine pulley and debris shield.

5.Remove engine pulley and belt from debris shield.

TO REPLACE DRIVE BELT (See Fig. 15)

1.Place new drive belt in engine pulley and belt retainer of debris shield.

2.Route the other end of the new drive belt through hole in housing.

3.Reinstall debris shield.

4.Return mower to upright position.

5.Install new belt on gearcase pulley.

6.Reinstall belt keeper and drive cover.

NOTE: Always use factory approved belt to assure proper fit and long life.

7.Turn lawn mower on its side with air filter and carbu- retor down.

8.Reinstall blade.

ENGINE PULLEY

BELT

BELT RETAINER

DEBRIS SHIELD

FIG. 15

MOWING

MOWING

POSITION

POSITION

HAIRPIN

 

 

COTTER

 

HANDLE

 

 

MOUNTING

 

BRACKET

 

 

PIN

LOW POSITION

HIGH POSITION

FIG. 16

LOWER

HANDLE

ROTATE

FIG. 17

ENGINE

Maintenance, repair, or replacement of the emission con- trol devices and systems, which are being done at the customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST HANDLE (See Figs. 16 and 17)

The handle can be mounted in a high or low position. The mounting holes in the bottom of lower handle are off center for raising or lowering the handle.

1.Remove upper handle and all wire tie(s) securing cable(s) to lower handle.

2.Remove hairpin cotters from lower handle bracket mounting pin.

3.Squeeze lower handle in to remove it from mounting pins.

4.Turn lower handle over to raise or lower handle.

5.Squeeze lower handle in and position holes onto mounting pins on handle bracket.

6.Reassemble upper handle and all parts removed from lower handle.

ENGINE SPEED

Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that the engine is running too fast or too slow, take your lawn mower to an authorized service center for repair and adjustment.

CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your lawn mower to an authorized service center for repair and/or adjustment.

IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO

13MAKE ANY NECESSARY ADJUSTMENTS.

Image 13
Contents 5521 CHV II. Slope Operation Safe Operation Practices for Walk-Behind MowersGeneral Operation III. ChildrenTable of Contents HOW to SET UP Your Lawn Mower AssemblyTo Install Attachments To Remove Lawn Mower from CartonOperation Meets Cpsc Safety RequirementsKnow Your Lawn Mower Engine Speed HOW to USE Your Lawn MowerEngine Zone Control To Convert MowerTo Empty Grass Catcher See Fig Before Starting EngineADD OIL See Fig To Stop Engine ADD Gasoline See FigTo Start Engine See Fig Mowing TipsGeneral Recommendations MaintenanceLawn Mower Lubrication ChartGrass Catcher EngineGear Case To Change Engine OIL See FigsCleaning Service and AdjustmentsTo Replace Drive Belt See Fig To Adjust Handle See FigsCarburetor Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsPage KEY Part Description Page 532 40 Warranty Statement