Husqvarna 5524SE owner manual KEY Part Description

REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 5224SE (96193000200), PRODUCT NO. 961 93 00-02

KEY	PART
NO.	NO.	DESCRIPTION

4532 19 10-79 Pulley, Impeller

5532 18 89-09 Bearing Assembly, Flange

6532 15 53-77 Nut, Hex Flange 5/16-18

7	532 18 03-55	Bolt, Flat Head, Carriage 5/16-18 x 5/8
8	872 27 05-05	Bolt, Carriage 5/16-1 8 x 5/8

9532 17 88-20 Nut, Cage 3/8-16

10532 18 40-90 Housing, Auger

11532 18 40-96 Bar, Scraper

12532 18 40-95 Bracket, Corner Discharge

13532 17 53-22 Base, Discharge Chute

14	819 11 15-07	Washer, Flat
15	810 04 05-00	Washer, Lock 5/16
16	874 95 05-12	Screw, Hex Head 5/16-18 x 3/4

18532 17 95-82 Screw, Hex Head 5/16 x 1

19873 80 04-00 Nut, Hex Lock 1/4-20

20873 80 05-00 Nut, Hex Lock 5/16-18

21532 15 54-15 Washer, Flat 5/16

22532 18 40-94 Skid Plate, RH

23532 17 92-46 Washer, Nylon, Friction

24	872 27 05-06	Bolt, Carriage	5/16-18 x 3/4
25	532 18 56-00	Bolt, Shoulder	1/4-20
26	532 17 46-58	Bearing, Auger

27532 17 46-97 Washer, Thrust, 1"

28532 19 20-90 Bolt, Shear

29 532 18 40-93 Skid Plate, LH

30532 19 94-74 Auger Assembly, RH

31532 19 94-73 Auger Assembly, LH

32532 17 46-99 O-Ring

33532 17 47-00 Bushing, Flange 3/4

34532 17 46-81 Washer, Thrust 3/4

35532 17 46-84 Bearing, Thrust 3/4

36532 17 46-60 Shaft, Impeller

37532 17 46-83 Washer, Thrust 5/8

38532 17 46-86 Bushing, Flange 5/8

39 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4

40532 08 64-47 Plug, Case

41532 17 46-88 Housing, Gearbox, RH

42532 17 46-98 Seal, Oil

43532 17 47-01 Bushing, Flange, 1"

44	532 18 92-82	Key, Square 1/4 x 1/4 x 7/8
45	532 17 46-59	Gear, Worm
46	532 17 46-57	Shaft, Auger

47532 17 46-87 Housing, Gearbox, LH

48532 18 41-05 Impeller Assembly

49	874 78 04-26	Screw, Hex Head 1/4-20 x 1-5/8
50	532 17 53-11	Gasket, Gearbox
51	532 18 42-05	Pin, Roll 3/16 x 1-1/8

54532 05 38-47 Washer, Flat 1/4

55532 18 82-43 Kit, Shear (Contains 6 each of Key Numbers 19 and 28)

56532 18 06-84 Multi-Wrench

57532 17 88-77Gearbox Assembly

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

21