Husqvarna 5524SE owner manual Repair Parts

Page 23

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 5224SE (96193000200), PRODUCT NO. 961 93 00-02

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 18 33-34

Knob, Lever

2

817 50 10-10

Screw #10-24 x 5/8

3

532 18 41-14

Strap, Slotted

4

873 80 06-00

Nut, Lock 3/8-16

5

819 13 13-16

Washer, Flat 3/8

6

532 17 86-59 Control Assembly, Chute Rotater

7

532 18 40-89

Support, Pivot

8

532 15 00-78

Screw, Hex Head 5/16-18 x 3/4

9532 18 04-53 Knob, Deflector

10532 18 56-00 Bolt, Shoulder

11532 05 38-47 Washer, Flat 1/4

12873 80 04-00 Nut, Lock 1/4-20

13 872 27 05-05 Bolt, Carriage 5/16-18 x 5/8

14532 17 92-46 Washer, Nylon

15532 18 41-12 Chute Assembly

16532 18 41-13 Deflector Assembly

17532 17 91-45 Seal, Deflector

18532 12 84-15 Rivet, Blind

19532 18 33-33 Knob, Speed Control Lever

20

872 27 05-06

Bolt, Carriage 5/16-18 x 3/4

21

532 15 54-15

Washer, Flat 5/16

24

874 78 05-28

Screw, Hex Head 5/16-18 x 1-3/4

25532 15 53-77 Nut, Lock 5/16-18

26532 19 88-75 Lever Assembly, Speed Control

27532 16 96-75 Retainer, Hairpin

28532 18 04-45 Rod, Upper, Speed Control

29532 18 77-16 Rod, Lower, Speed Control

30532 19 27-10 Clamp, Clean-Out Tool

31532 19 21-99 Tool, Clean-Out

32873 80 05-00 Nut, Lock 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

23

Image 23
Contents 5524SE Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsEngine HOW to USE Your Snow ThrowerStopping AugerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Lubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Repair Parts KEY Part Description Control Panel / Discharge Chute Repair Parts Repair Parts Handles Handles Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals KEY Part Description Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta