Husqvarna 532 44 00-55, 96045002800 To Replace Motion Drive Belt See Fig, To Check Brake

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 38)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Disconnect clutch wire harness (A).

3.Remove anti-rotation link (B) on right side of tractor.

4.Removebeltfromstationaryidler(C)andclutchingidler(D).

5.Remove belt from centerspan idler (E).

6.Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

7.Remove belt downward from engine pulley and around electric clutch (G).

8.Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

2.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pul- ley (F). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (E).

5.Installbeltthroughstationaryidler(C)andclutchingidler(D).

6.Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

7.Reconnect clutch harness (A).

8.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

9.Install mower (See “TO INSTALL MOWER” section in

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL (See Fig. 39)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

this manual).

B A

G

H

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

 

C

D

J

 

E

F

02953 electric

Fig. 39

Fig. 38

23

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents LGT2554 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Skid AssemblyTools Required for Assembly Unassembled PartsSET Parking Brake Lever and Lower AT- Tachment Lift See Fig Adjust Seat See FigTo Install Mower and Drive Belt See Figs ANTI-SWAY BAR S Install ANTI-SWAY BAR S if Equipped SeeTurn Steering Wheel Left and Position Mower See Fig Attach Front Link E See Fig Attach Mower Side Suspension Arms a to Chassis See FigAttach Rear Lift Links C See Fig Check for Proper Position of ALL Belts Install Belt on Engine Clutch Pulley M SeeCheck Tire Pressure Check Deck LevelnessOperation DPH AC J Know Your TractorTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig Stopping See FigTo Operate Mower To Adjust Gauge Wheels See FigTo Adjust Mower Cutting Height See Fig To Move Forward and Backward See FigTo Transport See Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig To Replace Mower Blade Drive Belt See Fig Service and AdjustmentsTo Install Mower To Remove Mower See FigTo Level Mower To Remove Wheel See Fig To Replace Motion Drive Belt See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Remove CABLES, Reverse Order Transaxle Motion Control Lever Neutral Adjustment See FigTo Start Engine with a Weak Battery See Fig To Attach Jumper CablesTransmission Engine OIL StorageOther Fuel SystemProblem Cause Correction Engine continues To run when operBattery will not Fires when turnTractor Model NO. LGT2554 96045002800, Product no 45 SchematicElectrical KEY Part Description Chassis Tractor Model NO. LGT2554 96045002800, Product no 45 Drive Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr Mower Deck 532 19 56-32 Deck Weldment Mower 30!2+ª!22%34%2ª+4 Engine532 42 Seat Seat AssemblySteering Assembly Mower Lift Wheels and Tires DecalsOnly Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission 11.02.10 JA
Top Page Image Contents