Husqvarna 532 42 57-62, 96045001800 owner manual Chassis

Page 31

TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18

CHASSIS

KEY	PART
NO.	NO.	DESCRIPTION
3	532 40 50-12	Logo
5	532 40 87-03	Dash
14	532 41 10-46	Hood
15	532 19 89-07	Lens LH
18	532 40 86-07	Grille/Lens Asm.
25	532 19 89-06	Lens RH
34	532 19 61-25	Plate Engine
36	817 06 05-12 Screw 5/16-18 x 3/4
37	532 41 87-14	Fender
52	873 68 05-00 Nut Lock 5/16-18
58	532 41 22-80 Drawbar Upper 2PC Sml. Fender
68	817 49 05-08 Screw Thdrol 5/16-18 x 1/2
130	532 41 63-58 Screw #10 x 0.750
137	532 40 75-90	Bumper Dash
138	532 40 29-54	Cupholder
150	532 19 85-13	Air Duct
151	532 41 02-50 Bracket Pivot Hood
152	532 19 95-35	Shield Browning
159	817 00 06-12 Screw 3/8-16 x 3/4
162	532 14 24-32	Screw
165	532 19 68-26 Support Tank Rear
175	532 19 63-04	Crossmember

176532 40 07-76 Screw 10-24 x 5/8

177532 19 52-27 Bushing Steering

178	532 19 97-82	Cargo Net Asm.
180	532 41 50-63	Chassis
181	532 40 30-25	Bushing Mtg. Fender Crgo
182	532 40 68-59	Dash Lower
183	874 78 05-20	Bolt Fin Hex 5/16-18 unc x 1-1/4

KEY	PART
NO.	NO.	DESCRIPTION
189	817 00 05-12 Screw 5/16-18 x 3/4

194873 90 05-00 Nut Lock Hex Flange 5/16-18

195532 40 41-37 Plug Hole Dash Lower

196532 41 45-80 Console Asm. Deck Lift

202532 40 30-48 Vent Side Hood RH

203532 40 30-76 Vent Side Hood LH

204 532 41 66-13 Vent Top Hood

205532 40 17-09 Skirt Hood Side RH

206532 40 17-11 Skirt Hood Side LH

207	532 19 71-98	Bezel RH
208	532 19 71-99	Bezel LH

209532 19 91-30 Insert Hex Top RH

210532 19 91-31 Insert Hex Top LH

211532 19 91-32 Insert Hex Bottom RH

212532 19 91-33 Insert Hex Bottom LH

213874 76 05-12 Bolt 5/16-18 x 3/4

214532 19 91-45 Clip Retainer Tinner

217	532 40 91-67	Rod Pivot
218	532 19 63-95	X-Piece Hood Stop
228	532 19 51-61	Stud Fastner
234	532 40 47-42	Bumper Hood
235	532 40 61-29	Spacer Fender
236	873 93 05-00	Nut Lock 5/16-18 unc
238	532 40 86-06	Trim
239	532 11 04-52	Nut, Push
287	817 60 04-06	Screw 1/4-20 x 3/8

NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

31

Image 31

Contents YTH20K46 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents To Remove Tractor from Carton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged To SET Parking Brake See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Operate on Hills To Operate Mower See FigTo Stop Mower Blades Reverse Operation System ROS See FigADD Gasoline Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission Mowing TipsLubrication Chart MaintenanceBlade Removal See Fig BatteryTractor Blade CareEngine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission To Adjust Throttle Control CableTo Adjust Carburetor REMOVAL/REPLACEMENTEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model Number YTH20K46 96045001800, Product no 45 SchematicElectrical KEY Part Description Chassis Chassis Drive KEY Part NO. NO. Description Engine Spark Arrester KITEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045001800, Product no 45 Wheels and Tires Decals532 40 Seat Seat AssemblyMower Deck KEY Part NO. no Description Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 42 57-62 Rev 1 05.11.09 TH