Husqvarna 532 42 57-62, 96045001800 owner manual Unassembled Parts, Tools Required for Assembly

Page 5

UNASSEMBLED PARTS

Slope Sheet

Key

(1) Oil Drain Tube

(2) Keys

ASSEMBLY

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)	1/2" wrench	Tire pressure gauge
(2)	7/16" wrenches	Utility knife
		Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

LABEL

Fig. 1

ADJUST SEAT (See Fig. 2)

•Sit in seat.

•Lift up adjustment lever (A) and slide seat until a com- fortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

BEFORE REMOVING TRACTOR FROM SKID

TO CHECK BATTERY (See Fig. 1)

•Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions).

•For battery and battery cable installation see "RE- PLACING BATTERY" in the "Service and Adjustments" section in this manual.

A

Fig. 2

NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid.

5

Image 5

Contents YTH20K46 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts To Remove Tractor from CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigSystem Characteristics To Move Forward and Backward See FigTo Stop Mower Blades To Operate Mower See FigReverse Operation System ROS See Fig To Operate on HillsBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsLubrication Chart MaintenanceTractor BatteryBlade Care Blade Removal See FigEngine Muffler CleaningSpark Plugs IN-LINE Fuel Filter See FigTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableREMOVAL/REPLACEMENT TransmissionOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model Number YTH20K46 96045001800, Product no 45 SchematicElectrical KEY Part Description Chassis Chassis Drive KEY Part NO. NO. Description Engine Spark Arrester KITEngine Kohler Model No. SV600 Steering Assembly Tractor - Model Number YTH20K46 96045001800, Product no 45 Wheels and Tires Decals532 40 Seat Seat AssemblyMower Deck KEY Part NO. no Description Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 42 57-62 Rev 1 05.11.09 TH