Husqvarna 96045002200 To Adjust Mower Cutting Height See Fig, To Adjust Gauge Wheels See Fig

Page 10

OPERATION

J

K

L

FIG. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 9

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 " during the cool season and to over 3"during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively

high; the second to desired height.

10

 

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place. (See FIG. 10)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2348 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Transport See Figs Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigPurge Transmission Mowing TipsRunning General Recommendations MaintenanceMaintenance ScheduleBrake Operation BatteryTractor TiresEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig First Install ANTI-SWAY BAR S LBF To Level Mower Turn nut right Turn nut left To raise mowerTo Replace Mower Blade Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigWeak or Dead Fully Charged Battery To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Replace Headlight BulbTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILProblem Cause Correction Fires when turn To run when operBattery will not Engine continuesSchematic Tractor Model NO. YTH2348 96045002200, Product no 45Electrical KEY Part Description Chassis Chassis 204 532 41 Vent Top HoodDrive 197 196Tractor Model NO. YTH2348 96045002200, Product no 45 Spark Arrester KIT EngineEngine Power Rating Information KEY Part NO. NO. DescriptionSteering Assembly 532 41 Wheel, Steering 532 19 Mower Deck KEY Part NO. NO. Description Mower Lift Seat Assembly Decals Wheels and TiresSuggested Guide for Sighting Slopes for Safe Operation Service Notes Service Notes Warranty Statement
Top Page Image Contents