Husqvarna LGT2554, 96045001500, 531 30 96-85 Tractor, Blade Care, Blade Removal See Fig, Battery

Page 17

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 24)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 24

17

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 25)

•Raisemowertohighestpositiontoallowaccesstoblades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

 

CENTER HOLE

Fig. 25

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Raise seat/hood.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICEANDADJUSTMENTSsectionofthismanual).

Page 16 Page 18
Image 17
Page 16 Page 18
Contents LGT2554 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts Before Removing Tractor from SkidTo Install Mower See Figs To Adjust Seat See FigFirst Install ANTI-SWAY BAR S Assemble Front Wheel to Mower See FigLB M Check Tire Pressure Mower Drive Belt InstallationCheck Deck Levelness Check for Proper Position of ALL BeltsOperation DPH AC J Know Your TractorTo SET Parking BRAKESee Fig HOW to USE Your TractorStopping See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To Operate MowerUsing the Reverse Operation System Service REMINDER/HOUR MeterTo Transport See To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsLubrication Chart MaintenanceTractor BatteryBlade Care Blade Removal See FigEngine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level MowerFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Check Brake To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigSlide belt toward rear of tractor, off the steering plate Remove from tractorTo Start Engine with a Weak Battery See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Remove Wheel See Fig To Attach Jumper CablesTransmission Other StorageFuel System Engine OILProblem Cause Correction Battery will not To run when operFires when turn Engine continuesWheels and Tires DecalsKEY Part Description 532 42SCH12 SchematicElectrical KEY Part Description Chassis 532 19 ChassisDrive Tractor Model NO. LGT2554 96045001500, Product no 45 Engine Spark Arrester KIT532 40 Seat Seat AssemblySteering Assembly Tractor Model NO. LGT2554 96045001500, Product no 45 Mower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationEffective January 1 Policy

LGT2554, 531 30 96-85, 96045001500 specifications

The Husqvarna 96045001500, also known as the LGT2554, is a robust lawn tractor specifically designed for homeowners seeking a versatile and efficient machine for maintaining their lawns and gardens. This model stands out due to its powerful features, advanced technologies, and user-friendly characteristics, making it a popular choice among gardening enthusiasts.

At the heart of the LGT2554 is a reliable 54-inch cutting deck, which enables quick and efficient mowing of large areas. The cutting deck is designed with a reinforced structure for durability, ensuring it stands up to regular use. With multiple cutting height adjustments, users can achieve the desired lawn finish, from a low trim to a higher cut for different grass types.

The LGT2554 is powered by a strong, air-cooled engine that provides ample horsepower, contributing to excellent performance throughout various tasks. The engine is equipped with technology that promotes a clean and efficient operation, minimizing emissions and maximizing fuel efficiency. The hydrostatic transmission allows for smooth driving and ease of operation, eliminating the need for manual gear changes, which is particularly beneficial for users navigating varied terrain.

Another highlight of the Husqvarna LGT2554 is its ergonomic design. The tractor features an adjustable seat, giving users comfort during longer mowing sessions. The steering wheel is positioned for easy handling, and the control layout is intuitive, allowing for straightforward operation even for those new to lawn tractors.

This model is also equipped with several innovative technologies. The Smart Switch™ technology simplifies the starting process, providing ease of use. The cutting deck is designed with air induction technology, ensuring grass is lifted before cutting, resulting in a clean, even cut and improved grass health.

Additionally, the LGT2554 comes with built-in compatibility for various attachments, such as baggers, mulchers, and snow blades, enhancing its utility throughout the year. The durable chassis supports heavy-duty usage and provides stability on slopes or uneven ground.

Overall, the Husqvarna 96045001500, LGT2554, exemplifies a high-quality lawn tractor that combines reliability, performance, and user comfort. Its advanced features and technologies cater to a wide range of gardening needs, making it an ideal choice for homeowners who prioritize maintaining a perfectly manicured lawn.
Top Page Image Contents