Husqvarna 372XPW manual Starting and Stopping, Starting and stopping, Cold engine, Warm engine

Page 19

STARTING AND STOPPING

Starting and stopping

WARNING! Note the following before

!starting:

The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting.

Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries.

Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything.

Keep people and animals well away from the working area.

Cold engine

Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards.

Ignition: Slide the ignition switch to the left.

Choke: Set the choke control in the choke position.

Start throttle: The correct choke/start throttle setting is obtained by moving the control to the choke position.

If the machine is fitted with a decompression valve (A): Press the valve to reduce the pressure in the cylinder and make starting easier. You should always use the decompression valve when starting the machine. Once the machine has started the valve will automatically return to its original setting.

A

Warm engine

Use the same procedure as for starting a cold engine but without setting the choke control in the choke position. The correct choke/start throttle setting is obtained by moving the choke control to the choke position and then pushing it in again.

Starting

Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly.Never wrap the starter cord around your hand

CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.

Push in the choke control as soon as the engine fire and make repeated starting attempts. Immediately press and release the throttle when the engine starts. That will disengage the throttle latch.

As the chain brake is still activated the engine must return to idling speed as soon as possible by disengaging the throttel latch in order to avoid unnecessery wear on the clutch assembly.

English – 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 372XPW You will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Muffler Stop switchCutting equipment Vibration damping systemSome terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainInstructions considerably increases the risk of kickback Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Sharpening cutting teethTensioning the chain General advice on adjusting depth gauge settingAdjustment of depth gauge setting If the depth gauge setting is too largeChecking chain lubrication Lubricating cutting equipmentChain oil Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules General Basic cutting techniqueTerms Cutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingFelling cut Cutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking the front hand guard Correctly adjusted carburetorHigh speed jet H Checking brake band wearChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Fitting the starter Air filterTensioning the recoil spring Changing a broken recoil springNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketHeated handles Air Injection centrifugal cleaningTemperature -5C 23F or colder Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data050/1,3 mm Saw chain filing and file gauges058/1,5 mm Your Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage ´z+R2G¶5¨ Page 1150183-95 ´z+R2G¶5¨ ´z+R2G¶5¨
Top Page Image Contents