Husqvarna 372XPW manual General rules

Page 22

WORKING TECHNIQUES

5Take great care when cutting a tree that is under tension. A tree that is under tension may spring back to its normal position before or after being cut. If you position yourself incorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control. Both situations can cause serious personal injury.

6Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance.

7When you put the chain saw on the ground, lock the saw chain using the chain brake and ensure you have a constant view of the machine. Switch the engine off before leaving your chain saw for any length of time.

General rules

1If you understand what kickback is and how it happens then you can reduce or eliminate the element of surprise. By being prepared you reduce the risk. Kickback is usually quite mild, but it can sometimes be very sudden and violent.

2Always hold the chain saw firmly with your right hand on the rear handle and your left hand on the front handle. Wrap your fingers and thumbs around the handles. You should use this grip whether you are right-handed or left- handed. This grip minimizes the effect of kickback and lets you keep the chain saw under control. Do not let go of the handles!

3Most kickback accidents happen during limbing. Make sure you are standing firmly and that there is nothing in the way that might make you trip or lose your balance.

Lack of concentration can lead to kickback if the kickback zone of the bar accidentally touches a branch, nearby tree or some other object.

Have control over the workpiece. If the pieces you intend to cut are small and light, they can jam in the saw chain and be thrown towards you. Even if this does not need to be a danger, you may be surprised and lose control of the saw. Never saw stacked logs or branches without first separating them. Only saw one log or one piece at a time. Remove the cut pieces to keep your working area safe.

4Never use the chain saw above shoulder height and avoid cutting with the tip of the bar. Never use the chain saw one-handed!

5In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support.

22 – English

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 372XPW Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchCutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral information on sharpening cutting teeth Instructions considerably increases the risk of kickbackIf the depth gauge setting is too large General advice on adjusting depth gauge settingAdjustment of depth gauge setting Tensioning the chainFilling with chain oil Lubricating cutting equipmentChain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Assembly Fitting the bar and chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules General Basic cutting techniqueTerms Limbing CuttingFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts FellingFelling cut Freeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Checking brake band wear Correctly adjusted carburetorHigh speed jet H Checking the front hand guardChecking the brake trigger Starter MufflerChanging a broken or worn starter cord Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Saw chain filing and file gauges058/1,5 mm Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage ´z+R2G¶5¨ Page 1150183-95 ´z+R2G¶5¨ ´z+R2G¶5¨
Top Page Image Contents