Husqvarna 968999189 / ZTH6123KOLA manual Pump belt, Lubrication, Tire pressure, Caster Wheels

Page 21

MAINTENANCE

Pump belt

Check belt every 100 hours for excessive wear. To replace belt. Relieve tension on the deck belt and remove deck belt from clutch. See deck belt instructions on previous page. Loosen bolt on the clutch tie down and rotate out of the way. Using a 1/2” drive ratchet inserted into the square hole in the pump idler arm relieve the tension on the pump belt and remove belt. To reinstall belt. Swing pump idler pulley out toward engine to route belt around it. Then route belt around right side pulley first as you are looking up from the underside of machine. Reinstall idler spring and use the ratchet to rotate idler so the belt may be installed all the way around the last pulley.

Lubrication

See service decal under foot plate for service points and maintenance intervals. Clean grease zerks thoroughly before greasing. See engine manual for engine service. FIG - 17

Tire pressure

Check every 25 hours. All four tires require 15 psi.

Caster Wheels

Check every 200 hours. Lift front of unit off of ground so caster wheels can rotate freely. Tighten caster bolt then back off 1/2 turn. Check that wheel rotates freely. If wheel does not rotate freely back the caster bolt off in 1/4 turn incre- ments until wheel rotates freely.

Fuel filter

Replace every 500 hours or annually. In ex- tremely dirty conditions replacement may need to be at shorter intervals.

Winter storage

To prepare the machine for storage. Clean the machine, especially under the deck. Touch-up the paint or spray the underside of deck with a light coat of oil.

Inspect the machine for damage and loose hardware.

Change the oil.

Drain the fuel system or add stabilizer to fuel. Make sure to run the machine after to circulate stabilizer throughout system.

Remove the plugs and add 1 tablespoon of oil in each cylinder. Install plugs and crank the engine two or three revolutions.

Grease all zerks.

Remove battery and store inside and protect it from freezing temperatures.

SERVICE DECAL

FIG - 17

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Manual no REV. IR 09/01/03 Operators manualHusqvarna. All rights reserved Contents Introduction IntroductionGood Service Symbols and Decals Symbols and DecalsSafety Instructions Safety InstructionsGeneral Use Keep children away from the work area Do as follows Driving on SlopesChildren Maintenance8011-563 Important Information TransportPresentation PresentationSetup Setup and AdjustmentsAdjustments Cutting HeightThrottle Lever Tension Mower Deck LevelingMotion Control Linkage Adjustment Park Brake AdjustmentOperating instructions Operating InstructionsStarting and operation ControlsOperating Instructions Safety interlock system MaintenanceCutter Housings Engine oilAir filter HardwareHydraulic system Deck beltLubrication Pump beltTire pressure Caster WheelsTorque Specifications Maintenance Schedule Problem Trouble ShootingWiring Diagrams Console Harness Schematic Harness Frame Frame Harness

968999224 / ZTH6127KOB, 968999225 / ZTH7227KOB, 968999189 / ZTH6123KOLA specifications

Husqvarna has long been a trusted name in outdoor power equipment, and their ZTH series of zero-turn mowers further cements this reputation. Among the offerings are the models 968999224 (ZTH6127KOB), 968999225 (ZTH7227KOB), and 968999189 (ZTH6123KOLA), each designed to deliver exceptional performance and efficiency for both residential and commercial users.

The ZTH6127KOB is equipped with a robust 27 HP engine, providing ample power for tackling large lawns with heavy grass and uneven terrain. Its 61-inch cutting deck ensures a wide cutting path, allowing for faster mowing and reduced time spent on the job. The deck features an innovative design that optimizes airflow for cleaner cuts and better grass lift, resulting in a superior finish.

The ZTH7227KOB takes things a step further with its powerful 27 HP engine and expansive 72-inch cutting deck. This model is particularly well-suited for commercial landscapers who need to cover large areas quickly. The mower’s heavy-duty frame and reinforced components ensure durability and reliability under demanding conditions.

Meanwhile, the ZTH6123KOLA, with its 23 HP engine, offers a slightly smaller yet highly efficient option. Its 61-inch cutting deck strikes the perfect balance for homeowners and small commercial operations looking for an agile yet powerful mower. All models come equipped with intuitive controls and ergonomic seating designed for hours of comfortable operation.

Technologically, all three models boast advanced features such as electronic fuel injection, which enhances fuel efficiency and provides smoother acceleration. The Hydro-Gear transmission ensures a responsive and agile maneuverability, allowing operators to navigate tight spaces with ease. The mowers also feature easy-to-use height adjustment systems for customizing cutting heights based on grass types and conditions.

Safety is a priority, and Husqvarna has equipped these models with ROPS (Roll Over Protection System) and an automatic blade brake that enhances operator safety while in operation. Each model combines high performance, efficiency, and comfort, making them ideal choices for anyone seeking a reliable solution for lawn maintenance.

From commercial users to homeowners, the ZTH series by Husqvarna proves to be an investment in quality and performance, reaffirming the brand’s commitment to excellence in lawn care technology.
Top Page Image Contents