Husqvarna TS300-E3 manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 29

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents LT1597 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTo Remove Tractor from Carton Unpack CartonInstall Seat See Figs a and 3B To Adjust SeatCheck Deck Levelness Attach Hood Scoop See FigCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor To SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigsTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigUsing the Reverse Operation System Reverse Operation System ROS See FigBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartTractor BatteryBlade Removal See Fig Engine To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Service and Adjustments To Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigTo Check Brake Front Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 41 01-85 Rev 04.02.08 AP
Top Page Image Contents