ENGLISH
DIGITAL COPY
Select the digital source of the DIGITAL output with or button for digital dubbing to the
The source is switched in the following sequence.
SOURCE → DIG.1 → DIG.2 → DIG.3 → DIG.4 → OFF → SOURCE → To determine each source, display the desired source and press the OK button or / button.
Notes:
VCR1 and TAPE outputs can only send a signal from an analog source connected to the AV9000. If you select a source which is only connected to a digital input, no signal will be available to ouput to a VCR1 or TAPE deck from the analog output. If you expect to do dubbing from digital source equipment to analog equipment, then you should connect the digital equipment's analog outputs into the AV9000's analog inputs in addition to making the digital connections. Conversely, a digital source may only be dubbed using the DIGITAL output, which must in turn be connected to a digital input of a digital recording device such as the
BASIC OPERATION
LISTENING TO THE TUNER
MANUAL TUNING
1.To select the tuner as the source, turn the INPUT SELECTOR knob !9on the front panel or press the TUNER button . on the remote.
2.Press the BAND button D4 on page 1 at TUNER MODE on the remote to select the desired frequency band if required.
3.Press the AUTO TUNING button !4on the AV9000 to display the frequency.
4.Turn the GYRO TUNING knob !6on AV9000 or press or button on the remote.
5.If FM is selected, press the MODE button D5 on the remote to select the desired audio mode.
AUTO TUNING (USING THE AV9000)
Light up the “AUTO TUN” indicator by pressing the AUTO TUNING button !4and turn the GYRO TUNING knob !6.
MULTI ROOM SELECT
MULTI ROOM SELECT
�
MULTI ROOM : OFF
VISUAL : TV
AUDIO : TUNER
VOLUME : VARIABLE
LEVEL : - 90dB
RETURN TO MAIN/EXIT
MULTI ROOM: To switch on the
VISUAL: Select the visual source of the
or button.
AUDIO: Select the audio source of the
or button.
VOLUME: Select whether the
LEVEL: Adjust the
Notes:
As described in the notes above,
If “VOLUME” is set to “FIXED”, the
STATION NAME INPUT
STATION NAME INPUT
�
PRESET NUMBER : 1
FM | 87 .50 MHz AUTO |
NAME : | : |
CHARACTERS |
ABCDEFGHIJKLMNOPQRST
UVWXYZ1234567890 – + /
RETURN TO MAIN/EXIT
Use this menu to add names to your preset stations.
1.Enter the preset number you wish to name using the PRESET button !5and then scrolling with the GYRO TUNING knob !6 until you reach the desired preset station.
2.The station will be displayed (including the name if you have already assigned one). In either case, the cursor will blink at the first letter of the station name.
3.Press the OK button or use the / buttons on the remote to position the cursor where you want it.
4.Use the / buttons to select the disired character
5.Place the cursor over the character you wish to enter using the/ / / buttons. Press the OK button when you are at the character you want.
6.Repeat steps 3 to 5 to enter additional characters. You can enter
up to 8 characters in total. | 14 |
AUTO TUNING (USING THE REMOTE CONTROL UNIT)
or button is pressed for more than 1 second to start Auto tuning function.
(FM) MODE Button Operation
When “AUTO” indicator is on in the display, FM stations which broadcast in stereo will be received in stereo and the “STEREO” indicator lights.
When “AUTO” indicator is off, all the FM stations will be received in monaural regardless of whether or not they are broadcasting in stereo.
PRESET TUNING
With this unit you can preset up to 50 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired.
1-a. Manual Presetting (Using the AV9000)
1.Refer to the “MANUAL TUNING” or “AUTO TUNING” section above to tune in a desired station.
2.Press the MEMO button !8. “MEMO” indicator starts blinking on the display. While “MEMO” is still blinking (approx. 5 seconds), select the preset number by turning the GYRO TUNING knob !6, then press the MEMO button again.
3.When a number has been properly input, “MEMO” indicator stops blinking and goes out. The station is now stored in the specified preset memory location.
1-b. Manual Presetting (Using the remote unit)
1.Tune in a desired station.
2.Press the M (MEMO) button ⁄3.
3.Enter the desired preset number with ten keypad ⁄2.
*When entering a single digit number (2, for example), either input “02” or just input “2” and wait for a few seconds.
*If a number other than
2.Auto Presetting
This function automatically scans the AM and FM band and enters all stations with proper signal strength into the memory.
This function is available only for AV9000.
1.Press the BAND button D4 on page 1 at TUNER MODE on the remote to select the FM band.
2.Tune in the lowest receivable frequency.
3.While pressing the MEMO button !8, turn the GYRO TUNING knob !6to up. Auto memory starts at this point.
4.“MEMO ” will blink on the display.
5.Each time the tuner finds a station, the scanning will pause and