Husqvarna 340e, 350 manual Cutting equipment designed to reduce kickback

Page 11

GENERAL SAFETY PRECAUTIONS

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or the

!wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well-maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating saw

!chain can cause extremely serious injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

•Length (inches/cm)

•Number of teeth on bar tip sprocket (T).

•Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

•Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

•Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

•Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

•Chain pitch (inches)

•Drive link width (mm/inches)

•Number of drive links.

Sharpening your chain and adjusting depth gauge setting

General information on sharpening cutting teeth

•Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. If the chain is very blunt it will produce wood powder and no chips or shavings.

•A sharp chain eats its way through the wood and produces long, thick chips or shavings.

•The cutting part of the chain is called the cutter and consists of a cutting tooth (A) and the depth gauge (B). The cutters cutting depth is determined by the difference in height between the two (depth gauge setting).

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 340 340e 345e Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingSharpening cutting teeth General advice on adjusting depth gauge settingAdjustment of depth gauge setting Filling with chain oil Tensioning the chainLubricating cutting equipment Chain oilChecking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication To prolong the life of the bar you should turn it over daily Fitting the bar and chain AssemblyFuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueGeneral Cutting LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionDirectional cuts FellingCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment High speed jet H Correctly adjusted carburetorThrottle lock Changing a broken or worn starter cord MufflerStarter Fitting the starter Replacement of broken recoil and drive disc springsAir filter Tensioning the recoil springNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Cooling systemDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage ´z+R#¶5E¨ Page 1150039-95 ´z+R#¶5E¨ ´z+R#¶5E¨
Related manuals
Manual 4 pages 16.3 Kb
Top Page Image Contents