Husqvarna 340e, 350 manual Air filter, Tensioning the recoil spring, Fitting the starter

Page 33

MAINTENANCE

Tensioning the recoil spring

Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/ 2 turn when the starter cord is pulled all the way out.

Replacement of broken recoil and drive disc springs

Recoil spring (A)

Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.

Remove the cassette with the recoil spring from the starter.

Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Drive disc spring (B)

Undo the bolt in the centre of the pulley and remove the drive disc and the drive disc spring.

Replace the drive disc spring and fit the drive disc above the spring.

A

B

Fitting the starter

To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts

Excessive fuel consumption.

Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice.

English – 33

Image 33
Contents 340 340e 345e KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Chain catcher Throttle lockRight hand guard Vibration damping systemCutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingGeneral advice on adjusting depth gauge setting Adjustment of depth gauge settingSharpening cutting teeth Lubricating cutting equipment Tensioning the chainChain oil Filling with chain oilChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment To prolong the life of the bar you should turn it over daily Fitting the bar and chain AssemblyFuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsGeneral rules Basic cutting technique GeneralTerms Cutting LimbingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatDirectional cuts FellingFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral High speed jet H Correctly adjusted carburetorThrottle lock Muffler StarterChanging a broken or worn starter cord Air filter Replacement of broken recoil and drive disc springsTensioning the recoil spring Fitting the starterSpark plug Adjustment of the oil pumpLubricating the bar tip sprocket Needle bearing lubricationTemperature 0C 32F or colder Air Injection centrifugal cleaningCooling system Winter useDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsYour Warranty Rights and Obligations Federal Emission Control Warranty StatementSafety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage ´z+R#¶5E¨ Page 1150039-95 ´z+R#¶5E¨ ´z+R#¶5E¨
Related manuals
Manual 4 pages 16.3 Kb