Husqvarna 1151375-95 General requirements working at height, Preparing to use the saw in the tree

Page 23

WORKING TECHNIQUES

user. If the saw chain is jamming, the saw may be pushed back at you.

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which can lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling chain. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting with a pulling chain gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Working with tree service chain-saws from a rope and harness

This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a rope and harness. While it may form the basis of guidance and training literature, it should not be regarded as a substitute for formal training.

General requirements working at height

Operators of tree service chainsaws working at height from a rope and harness should never work alone. A competent ground worker trained in appropriate emergency procedures should assist them.

Operators of tree service chainsaws for this work should be trained in general safe climbing and work positioning techniques and shall properly equipped with harnesses, ropes, strops, karabiners and other equipment for maintaining secure and safe working positions for both themselves and the saw.

Preparing to use the saw in the tree

The chain saw should be checked, fuelled, started and warmed up by the ground worker and the chain brake should be engaged before it is sent up to the operator in the tree. The chainsaw should be fitted with a suitable strop for attaching to the operator’s harness:

a)choke the strop around the attachment point on the rear of the saw.

b)provide suitable karabiners to allow indirect (i.e. via the strop) and direct attachment (i.e. at the attachment point on the saw) of saw to the operators harness.

c)ensure the saw is securely attached when it is being sent up to the operator.

The saw should only be attached to the recommended attachment points on the harness. These may be at mid- point (front or rear) or at the sides. Where possible attaching the saw to centre rear mid-point will keep it clear of climbing lines and support its weight centrally down the operator’s spine.

When moving the saw from any attachment point to another, operators should ensure it is secured in the new position before releasing it from the previous attachment point.

Using the chainsaw in the tree

An analysis of accidents with these saws during tree service operations shows the primary cause as being inappropriate one-handed use of the saw. In the vast majority of accidents, operators fail to adopt a secure work position witch allows them to hold both handles of the saw. This results in an increased risk of injury due to:

•not having a firm grip on the saw if it kicks back.

•a lack of control of the saw such that it is more liable to contact climbing lines and operators body (particularly the left hand and arm)

•loosing control from insecure work position resulting in contact with the saw (unexpected movement during operation of the saw)

Securing the work position for two-handed use

To allow the operator to hold the saw with both hands, they should as general rule, aim for secure work position where they are operating the saw at:

•hip level when cutting horizontal sections.

•solar plexus level when cutting vertical sections.

Where the operator is working close into vertical stems with a low lateral forces on their work position, then a good footing may be all that is needed to maintain a secure work position. However as operators move away from the

English – 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 334T 338XPT EPA III, Carb You will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Personal protective equipment Machine′s safety equipmentChain brake and front hand guard Vibration damping system Throttle lockoutChain catcher General rules Stop switchCutting equipment MufflerChain Sharpening your chain and adjusting depth gauge settingCutting equipment designed to reduce kickback BarToo large General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Bar and cause serious or even fatal injury Adjustment of depth gauge settingTensioning the chain Lubricating cutting equipmentChain drive sprocket Filling with chain oilChecking chain lubrication Checking wear on cutting equipment Working with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useDo not let go of the handles Securing the work position for two-handed use Using the chainsaw in the treeGeneral requirements working at height Preparing to use the saw in the treeBasic cutting technique Limbing Felling technique for tree topsLog is supported at both ends. There is a high risk Felling cut Felling directionDirectional cuts Cutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Cutting the trunk into logs How to avoid kickbackWhat is kickback? Carburetor MaintenanceChecking the front hand guard Correctly adjusted carburetorHigh speed jet H Checking brake band wearImmediately Changing a broken or worn starter cord MufflerStarter Fitting the starter Air filterTensioning the recoil spring Changing a broken recoil springLubricating the bar tip sprocket Adjustment of the oil pumpWhen making adjustments Spark plugDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinations, model 334TBar and chain combinations, model 338XPT Your Warranty Rights and Obligations What is not Covered Other safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage ´z+SE¶5j¨ Page 1151375-95

1151375-95, 338XPT EPA III specifications

The Husqvarna 338XPT is a powerful chainsaw designed specifically for professionals who require reliability and performance in demanding environments. One of its standout features is the lightweight design, making it easy to maneuver while still delivering impressive power. Weighing in at just over 10 pounds, the 338XPT allows users to work for extended periods without fatigue, making it an ideal choice for arborists and forestry workers.

At the heart of the Husqvarna 338XPT is its efficient engine, which not only provides robust cutting performance but is also designed with EPA III compliance in mind. This means the machine adheres to strict environmental regulations, producing lower emissions while ensuring a high power output. The X-Torq engine technology is one of the key innovations that contribute to its efficiency. This technology reduces fuel consumption by up to 20% while also decreasing harmful exhaust emissions. This dual benefit makes the 338XPT a viable option for users who prioritize both performance and environmental responsibility.

Another notable characteristic of the Husqvarna 338XPT is its advanced air filtration system, which enhances the durability of the engine by ensuring that only clean air reaches it. The centrifuge air cleaning system significantly prolongs the time between filter cleanings, allowing users to focus more on their work and less on maintenance. This feature is particularly beneficial in dusty or dirty job sites, ensuring optimal performance in various conditions.

Comfort and usability are also central to the design of the 338XPT. The chainsaw includes an ergonomic handle that allows for better control during operation, reducing vibrations and enhancing user comfort. Additionally, the chainsaw's easy-access chain tensioning system makes adjusting the chain as simple as possible, ensuring that users can quickly get back to their tasks at hand without unnecessary delays.

For safety-conscious users, the Husqvarna 338XPT is equipped with features like a combined choke/stop control that allows for easy starting and reduces the risk of engine flooding. Furthermore, the chainsaw's inherent balance and lightweight structure contribute to safer handling and operation.

In summary, the Husqvarna 338XPT EPA III is a top-of-the-line chainsaw that combines power, efficiency, and user-friendly features, making it a prime choice for professionals in the forestry and arborist fields. Its robust engine technology, advanced air filtration, and ergonomic design ensure that you can tackle any job with confidence and ease.
Top Page Image Contents