Husqvarna 1151375-95, 338XPT EPA III manual Tensioning the chain, Lubricating cutting equipment

Page 13

GENERAL SAFETY PRECAUTIONS

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off

! the bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nut that holds the clutch cover and chain brake. Use the combination spanner.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nut while holding up the tip of the bar. Check that you can pull the saw chain round freely by hand, and that there is no slack on the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

! equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which has a vegetable oil base. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous to you and damage the machine and environment.

IMPORTANT! When using vegetable based saw chain oil, dismantle and clean the groove in the bar and saw chain before long-term storage. Otherwise there is a risk of the saw chain oil oxidizing, which will result in the saw chain becoming stiff and the bar tip sprocket jamming.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 334T 338XPT EPA III, Carb Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard Chain catcher Throttle lockoutVibration damping system Cutting equipment Stop switchMuffler General rulesCutting equipment designed to reduce kickback Sharpening your chain and adjusting depth gauge settingBar ChainIncreased if the depth gauge setting is General advice on adjusting depth gauge settingToo large Tensioning the chain Adjustment of depth gauge settingLubricating cutting equipment Bar and cause serious or even fatal injuryChecking chain lubrication Filling with chain oilChain drive sprocket Checking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Fuel HandlingFueling Fuel safetyTransport and storage Long-term storageStarting and stopping Starting and StoppingCold engine Warm engineStopping Working Techniques Basic safety rulesBefore use General working instructionsDo not let go of the handles General requirements working at height Using the chainsaw in the treePreparing to use the saw in the tree Securing the work position for two-handed useBasic cutting technique Log is supported at both ends. There is a high risk Felling technique for tree topsLimbing Directional cuts Felling directionFelling cut Freeing a tree that has fallen badly General adviceCutting trees and branches that are in tension What is kickback? How to avoid kickbackCutting the trunk into logs Carburetor MaintenanceHigh speed jet H Correctly adjusted carburetorChecking brake band wear Checking the front hand guardImmediately Starter MufflerChanging a broken or worn starter cord Tensioning the recoil spring Air filterChanging a broken recoil spring Fitting the starterWhen making adjustments Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataBar and chain combinations, model 338XPT Bar and chain combinations, model 334TSaw chain filing and file gauges Your Warranty Rights and Obligations What is not Covered Safety precautions for chain saw users American Standard Safety PrecautionsKickback safety precautions Other safety precautionsPage ´z+SE¶5j¨ Page 1151375-95

1151375-95, 338XPT EPA III specifications

The Husqvarna 338XPT is a powerful chainsaw designed specifically for professionals who require reliability and performance in demanding environments. One of its standout features is the lightweight design, making it easy to maneuver while still delivering impressive power. Weighing in at just over 10 pounds, the 338XPT allows users to work for extended periods without fatigue, making it an ideal choice for arborists and forestry workers.

At the heart of the Husqvarna 338XPT is its efficient engine, which not only provides robust cutting performance but is also designed with EPA III compliance in mind. This means the machine adheres to strict environmental regulations, producing lower emissions while ensuring a high power output. The X-Torq engine technology is one of the key innovations that contribute to its efficiency. This technology reduces fuel consumption by up to 20% while also decreasing harmful exhaust emissions. This dual benefit makes the 338XPT a viable option for users who prioritize both performance and environmental responsibility.

Another notable characteristic of the Husqvarna 338XPT is its advanced air filtration system, which enhances the durability of the engine by ensuring that only clean air reaches it. The centrifuge air cleaning system significantly prolongs the time between filter cleanings, allowing users to focus more on their work and less on maintenance. This feature is particularly beneficial in dusty or dirty job sites, ensuring optimal performance in various conditions.

Comfort and usability are also central to the design of the 338XPT. The chainsaw includes an ergonomic handle that allows for better control during operation, reducing vibrations and enhancing user comfort. Additionally, the chainsaw's easy-access chain tensioning system makes adjusting the chain as simple as possible, ensuring that users can quickly get back to their tasks at hand without unnecessary delays.

For safety-conscious users, the Husqvarna 338XPT is equipped with features like a combined choke/stop control that allows for easy starting and reduces the risk of engine flooding. Furthermore, the chainsaw's inherent balance and lightweight structure contribute to safer handling and operation.

In summary, the Husqvarna 338XPT EPA III is a top-of-the-line chainsaw that combines power, efficiency, and user-friendly features, making it a prime choice for professionals in the forestry and arborist fields. Its robust engine technology, advanced air filtration, and ergonomic design ensure that you can tackle any job with confidence and ease.
Top Page Image Contents