Caster Housing Angle Adjustment | Invacare 1171880 instruction

12 CASTER

DETAIL “A” - INSIDE VIEW OF	DETAIL “B” - OUTSIDE VIEW OF
CASTER HOUSING		CASTER HOUSING	Base
Belleville Washer		Round Adjustment Nut
	Front Frame

Top Mounting Screw

Front Frame

Bottom Mounting

Caster Housing

Belleville Washer

Screw

Square Adjustment

Nut

FIGURE 5 Repositioning the Front Caster Housings

12.5Caster Housing Angle Adjustment

For this procedure, refer to FIGURE 6 on page 88.

The round adjustment nuts for smaller (fine tuning) angle adjustments. The square adjustment block is for larger angle adjustments.

Small Angle Adjustments

1.If necessary, loosen the top mounting screw (Detail “A”).

2.Position a large right triangle or “L” square on the ground/floor and against the caster fork (Detail “C”).

Invacare®Top End Reveal™Wheelchair

86

Part No 1171880

Image 86

Invacare 1171880 Caster Housing Angle Adjustment, Small Angle Adjustments, Belleville Washer Round Adjustment Nut

Contents

InvacareTop End RevealWheelchair Page Contents Seat Caster Symbols General Limited Warranty Wheelchair User SafetyGeneral Guidelines Wheelchair Tie Down Restraints Stability Warning Repair and Service Information Operating Information Tire Pressure and Information Weight TrainingSeat Positioning Straps Overview Label Locations Serial Number Component Identification Non Tapered front end Standard Typical Product Parameters0, +4, +8 Lock Down, Folding Standard Reveal RVL Weight Stability and Balance Safety/Handling of WheelchairsSafety/Handling of Wheelchairs SAFETY/HANDLING of Wheelchairs Lengthening Wheelbase Shortening Reaching, Leaning and Bending Forward Coping with Everyday Obstacles Reaching, Leaning BackwardsReaching, Leaning Bending Forward Backwards Tipping Tipping Curbs Stairways Moving Up Stairs Moving Down Stairs Stairways Escalators Transferring To and From Other Seats Inspect Initially Safety InspectionSafety Inspection Checklist Inspect/Adjust Weekly Inspect/Adjust Monthly Inspect/Adjust Periodically Troubleshooting Solutions Maintenance Maintenance Safety Precautions Suggested Maintenance Procedures  Tire wear is excessive if Replacing/Repairing Rear Wheel Tire/Tube Replacing/Repairing Caster Tire/Tube Footrest Adjusting/Replacing Standard FootrestAdjusting the Footrest Replacing/Adjusting Optional Adjustable Angle Footrest Replacing the Footrest Adjusting Footplate Angle Adjusting Footplate Depth Adjustments Clamp Replacing/Adjusting Optional Adjustable Angle Footrest Installing the Swingaway Padded Armrest Socket Arms Remove Back Stop Insert Right Side Armrest Socket Left Side Armrest Socket Install Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Removing Installing/Removing/Adjusting the Swingaway Padded ArmrestAdjusting Height  To remove the T-arm, reverse this procedure Adjusting T-Arm Height Back Unfolding/Folding the Back Detail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail This orientation Hole in adjustmentWhen installed Square will align with With 0 when Hole AdjustmentSquare will align with + when installed Seat Rail Orientation Adjustable Tension Back Upholstery Back Upholstery Cover Adjusting the Back Tension Removing the Back Upholstery Cover Removing the Adjustable Tension Back UpholsteryInstalling the Lumbar Strap Removing the Lumbar Strap Installing the Adjustable Tension Back Upholstery Installing the Back Upholstery Cover Detail a Detail B Back Canes Detail E Removing Foldover Back Upholstery Removing/Installing Foldover Back UpholsteryInstalling Foldover Back Upholstery Front Wheelchair Back Height Adjustment HOLE* Number Insert Back Cane Adjustment Pin Back CaneHole Number Removing/Installing the Back Frame Installing Seat Replacing Seat Upholstery Changing Seat Angle/Changing Rear Seat Height Height Adjustment Bar Bottom View Wheel Locks Replacing/Adjusting the Wheel LocksAdjusting the Wheel Lock Replacing the Wheel Lock Replacing/Adjusting the Wheel Locks Changing Wheel Lock Handle Position Configuration Converting From Pull-to-Lock to Push-to-Lock Removing/Installing Rear Wheels Wheels Adjusting Quick-Release Axles Removing/Installing Rear Wheels And/or Out Adjusting Quad-Release HandlesReplacing Quad-Release Axles Removing Play from Rear Wheels Adjusting Quad-Release Handle In and/or OutRemoving Play from Rear Wheels Handrim Replacement Handrim Replacement Adjusting Wheelbase Length Adjusting Center of Gravity COG Determining Wheelbase Length Wheels Mounting Screws Locknuts Frame Height Adjustment Bar Adjusting Wheelbase Width May be affected Removing the Camber Tube Removing/Installing the Camber TubeInstalling the Camber Tube Camber Tube Clamp AngleAxle Adjusting the Camber Tube Detail a Side View Determining/Setting Toe In/Toe Out  For this procedure, refer to on page 76 and Figure Top View of Wheelchair Top View of Wheelchair Adjusting Fork Tension Caster Detail a Detail B ONE Standard Fork Sided Fork Standard Forks Removing/Installing/Repositioning the Caster AssembliesInstalling Front Caster Removing Front Caster Removing Fork Assembly Installing the CasterRemoving/Installing the Fork Assembly One Sided Fork Installing Fork Assembly  Spacer orientation must be as shown in Figure Repositioning the Front Caster Housings  For this procedure, refer to on Belleville Washer Round Adjustment Nut Caster Housing Angle AdjustmentSmall Angle Adjustments Large Angle Adjustments Interference between Adjusting/Replacing Anti-tipper Anti-Tipper Adjusting Anti-tipper Replacing Anti-tipper Release Buttons Lock Buttons ANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair USA Canada