Reversing Anti-tipper Bracket Orientation | Invacare 1171880

13 ANTI-TIPPER

13.2 Reversing Anti-tipper Bracket Orientation

1.Press in the release buttons and remove the anti-tipper from the anti-tipper bracket.

2.Loosen, but DO NOT remove, anti-tipper mounting screws.

3.Remove the nut from the camber clamp mounting screws.

4.Slide anti-tipper brackets away from camber clamps exposing the spacer between them.

5.Remove camber tube. Refer to Removing/Installing the Camber Tube on page 75.

 Anti-tipper mounting screws should be the last screws to be tightened.

6.Install anti-tipper brackets onto opposite side of camber tube. Reverse procedure. Tighten fasteners securely.

7.Install camber tube. Refer to Removing/Installing the Camber Tube on page 75.

8.Install anti-tippers and adjust height. Refer to Adjusting/Replacing Anti-tipper on page 89.

Part No 1171880

93

Invacare®Top End Reveal™Wheelchair

Image 93

Invacare 1171880 user manual Reversing Anti-tipper Bracket Orientation

Contents

InvacareTop End RevealWheelchair Page Contents Seat Caster General Symbols Limited Warranty Safety General GuidelinesWheelchair User Stability Warning Wheelchair Tie Down Restraints Operating Information Repair and Service Information Weight Training Seat Positioning StrapsTire Pressure and Information Label Locations Serial Number Overview Component Identification 0, +4, +8 Typical Product ParametersNon Tapered front end Standard Lock Down, Folding Standard Reveal RVL Weight Safety/Handling of Wheelchairs Safety/Handling of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Reaching, Leaning and Bending Forward Lengthening Wheelbase Shortening Reaching, Leaning Backwards Reaching, Leaning Bending Forward BackwardsCoping with Everyday Obstacles Tipping Curbs Tipping Moving Up Stairs Stairways Stairways Moving Down Stairs Transferring To and From Other Seats Escalators Safety Inspection Safety Inspection ChecklistInspect Initially Inspect/Adjust Weekly Inspect/Adjust Periodically Inspect/Adjust Monthly Solutions Troubleshooting Suggested Maintenance Procedures Maintenance Maintenance Safety Precautions  Tire wear is excessive if Replacing/Repairing Caster Tire/Tube Replacing/Repairing Rear Wheel Tire/Tube Adjusting/Replacing Standard Footrest Adjusting the FootrestFootrest Replacing the Footrest Replacing/Adjusting Optional Adjustable Angle Footrest Adjusting Footplate Depth Adjusting Footplate Angle Replacing/Adjusting Optional Adjustable Angle Footrest Adjustments Clamp Arms Installing the Swingaway Padded Armrest Socket Remove Back Stop Insert Left Side Armrest Socket Right Side Armrest Socket Install Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Installing/Removing/Adjusting the Swingaway Padded Armrest Adjusting HeightRemoving Adjusting T-Arm Height  To remove the T-arm, reverse this procedure Unfolding/Folding the Back Back Detail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail When installed Hole in adjustmentThis orientation Square will align with Square will align with + when installed Hole AdjustmentWith 0 when Seat Rail Orientation Back Upholstery Cover Adjustable Tension Back Upholstery Adjusting the Back Tension Installing the Lumbar Strap Removing the Adjustable Tension Back UpholsteryRemoving the Back Upholstery Cover Removing the Lumbar Strap Installing the Back Upholstery Cover Installing the Adjustable Tension Back Upholstery Back Canes Detail a Detail B Detail E Installing Foldover Back Upholstery Removing/Installing Foldover Back UpholsteryRemoving Foldover Back Upholstery Front Wheelchair HOLE* Number Back Height Adjustment Adjustment Pin Back Cane Hole NumberInsert Back Cane Installing Removing/Installing the Back Frame Replacing Seat Upholstery Seat Changing Seat Angle/Changing Rear Seat Height Bottom View Height Adjustment Bar Adjusting the Wheel Lock Replacing/Adjusting the Wheel LocksWheel Locks Replacing the Wheel Lock Changing Wheel Lock Handle Position Replacing/Adjusting the Wheel Locks Converting From Pull-to-Lock to Push-to-Lock Configuration Wheels Removing/Installing Rear Wheels Removing/Installing Rear Wheels Adjusting Quick-Release Axles Adjusting Quad-Release Handles Replacing Quad-Release AxlesAnd/or Out Adjusting Quad-Release Handle In and/or Out Removing Play from Rear WheelsRemoving Play from Rear Wheels Handrim Replacement Handrim Replacement Determining Wheelbase Length Adjusting Wheelbase Length Adjusting Center of Gravity COG Wheels Mounting Screws Locknuts Frame Height Adjustment Bar May be affected Adjusting Wheelbase Width Removing/Installing the Camber Tube Installing the Camber TubeRemoving the Camber Tube Angle AxleCamber Tube Clamp Detail a Side View Adjusting the Camber Tube  For this procedure, refer to on page 76 and Figure Determining/Setting Toe In/Toe Out Top View of Wheelchair Top View of Wheelchair Caster Adjusting Fork Tension Detail a Detail B ONE Standard Fork Sided Fork Installing Front Caster Removing/Installing/Repositioning the Caster AssembliesStandard Forks Removing Front Caster Removing/Installing the Fork Assembly Installing the CasterRemoving Fork Assembly One Sided Fork  Spacer orientation must be as shown in Figure Installing Fork Assembly  For this procedure, refer to on Repositioning the Front Caster Housings Caster Housing Angle Adjustment Small Angle AdjustmentsBelleville Washer Round Adjustment Nut Large Angle Adjustments Interference between Anti-Tipper Adjusting/Replacing Anti-tipper Replacing Anti-tipper Adjusting Anti-tipper Lock Buttons Release Buttons ANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair Canada USA