Overview, Label Locations Serial Number | Invacare 1171880 specification

3 OVERVIEW

3 Overview

3.1Label Locations

Serial Number

Label Location

WEIGHT CAPACITY

250 LBS. (114 kgs.)

REFERTO OWNER’S MANUAL

P/N 1111013

Detent balls should extend beyond the diameter of the

WARNING axle bushing for a positive lock. Keep detent balls
clean.	P/N 1026960 Rev D

Invacare®Top End Reveal™Wheelchair

12

Part No 1171880

Image 12

Invacare 1171880 user manual Overview, Label Locations Serial Number

Contents

InvacareTop End RevealWheelchair Page Contents Seat Caster Symbols General Limited Warranty Safety General GuidelinesWheelchair User Wheelchair Tie Down Restraints Stability Warning Repair and Service Information Operating Information Weight Training Seat Positioning StrapsTire Pressure and Information Overview Label Locations Serial Number Component Identification Typical Product Parameters 0, +4, +8Non Tapered front end Standard Lock Down, Folding Standard Reveal RVL Weight Safety/Handling of Wheelchairs Safety/Handling of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Lengthening Wheelbase Shortening Reaching, Leaning and Bending Forward Reaching, Leaning Backwards Reaching, Leaning Bending Forward BackwardsCoping with Everyday Obstacles Tipping Tipping Curbs Stairways Moving Up Stairs Moving Down Stairs Stairways Escalators Transferring To and From Other Seats Safety Inspection Safety Inspection ChecklistInspect Initially Inspect/Adjust Weekly Inspect/Adjust Monthly Inspect/Adjust Periodically Troubleshooting Solutions Maintenance Maintenance Safety Precautions Suggested Maintenance Procedures  Tire wear is excessive if Replacing/Repairing Rear Wheel Tire/Tube Replacing/Repairing Caster Tire/Tube Adjusting/Replacing Standard Footrest Adjusting the FootrestFootrest Replacing/Adjusting Optional Adjustable Angle Footrest Replacing the Footrest Adjusting Footplate Angle Adjusting Footplate Depth Adjustments Clamp Replacing/Adjusting Optional Adjustable Angle Footrest Installing the Swingaway Padded Armrest Socket Arms Remove Back Stop Insert Right Side Armrest Socket Left Side Armrest Socket Install Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Installing/Removing/Adjusting the Swingaway Padded Armrest Adjusting HeightRemoving  To remove the T-arm, reverse this procedure Adjusting T-Arm Height Back Unfolding/Folding the Back Detail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail Hole in adjustment When installedThis orientation Square will align with Hole Adjustment Square will align with + when installedWith 0 when Seat Rail Orientation Adjustable Tension Back Upholstery Back Upholstery Cover Adjusting the Back Tension Removing the Adjustable Tension Back Upholstery Installing the Lumbar StrapRemoving the Back Upholstery Cover Removing the Lumbar Strap Installing the Adjustable Tension Back Upholstery Installing the Back Upholstery Cover Detail a Detail B Back Canes Detail E Removing/Installing Foldover Back Upholstery Installing Foldover Back UpholsteryRemoving Foldover Back Upholstery Front Wheelchair Back Height Adjustment HOLE* Number Adjustment Pin Back Cane Hole NumberInsert Back Cane Removing/Installing the Back Frame Installing Seat Replacing Seat Upholstery Changing Seat Angle/Changing Rear Seat Height Height Adjustment Bar Bottom View Replacing/Adjusting the Wheel Locks Adjusting the Wheel LockWheel Locks Replacing the Wheel Lock Replacing/Adjusting the Wheel Locks Changing Wheel Lock Handle Position Configuration Converting From Pull-to-Lock to Push-to-Lock Removing/Installing Rear Wheels Wheels Adjusting Quick-Release Axles Removing/Installing Rear Wheels Adjusting Quad-Release Handles Replacing Quad-Release AxlesAnd/or Out Adjusting Quad-Release Handle In and/or Out Removing Play from Rear WheelsRemoving Play from Rear Wheels Handrim Replacement Handrim Replacement Adjusting Wheelbase Length Adjusting Center of Gravity COG Determining Wheelbase Length Wheels Mounting Screws Locknuts Frame Height Adjustment Bar Adjusting Wheelbase Width May be affected Removing/Installing the Camber Tube Installing the Camber TubeRemoving the Camber Tube Angle AxleCamber Tube Clamp Adjusting the Camber Tube Detail a Side View Determining/Setting Toe In/Toe Out  For this procedure, refer to on page 76 and Figure Top View of Wheelchair Top View of Wheelchair Adjusting Fork Tension Caster Detail a Detail B ONE Standard Fork Sided Fork Removing/Installing/Repositioning the Caster Assemblies Installing Front CasterStandard Forks Removing Front Caster Installing the Caster Removing/Installing the Fork AssemblyRemoving Fork Assembly One Sided Fork Installing Fork Assembly  Spacer orientation must be as shown in Figure Repositioning the Front Caster Housings  For this procedure, refer to on Caster Housing Angle Adjustment Small Angle AdjustmentsBelleville Washer Round Adjustment Nut Large Angle Adjustments Interference between Adjusting/Replacing Anti-tipper Anti-Tipper Adjusting Anti-tipper Replacing Anti-tipper Release Buttons Lock Buttons ANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair USA Canada