Adjusting the Back Tension | Invacare 1171880 instruction

8 BACK

Adjusting the Back Tension

The adjustable tension back upholstery consists of an upper and lower (lumbar) section.

To adjust the back tension, perform the following

1.Lift back upholstery cover up and flip over toward front of wheelchair

2.Tighten or loosen the adjuster fastening straps.

Adjuster Straps

FIGURE 6 Adjustable Tension Back Upholstery - Adjusting the Back Tension

Part No 1171880

51

Invacare®Top End Reveal™Wheelchair

Image 51

Invacare 1171880 user manual Adjusting the Back Tension

Contents

InvacareTop End RevealWheelchair Page Contents Seat Caster General Symbols Limited Warranty Safety General GuidelinesWheelchair User Stability Warning Wheelchair Tie Down Restraints Operating Information Repair and Service Information Weight Training Seat Positioning StrapsTire Pressure and Information Label Locations Serial Number Overview Component Identification Lock Down, Folding Standard Typical Product Parameters0, +4, +8 Non Tapered front end Standard Reveal RVL Weight Safety/Handling of Wheelchairs Safety/Handling of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Reaching, Leaning and Bending Forward Lengthening Wheelbase Shortening Reaching, Leaning Backwards Reaching, Leaning Bending Forward BackwardsCoping with Everyday Obstacles Tipping Curbs Tipping Moving Up Stairs Stairways Stairways Moving Down Stairs Transferring To and From Other Seats Escalators Safety Inspection Safety Inspection ChecklistInspect Initially Inspect/Adjust Weekly Inspect/Adjust Periodically Inspect/Adjust Monthly Solutions Troubleshooting Suggested Maintenance Procedures Maintenance Maintenance Safety Precautions  Tire wear is excessive if Replacing/Repairing Caster Tire/Tube Replacing/Repairing Rear Wheel Tire/Tube Adjusting/Replacing Standard Footrest Adjusting the FootrestFootrest Replacing the Footrest Replacing/Adjusting Optional Adjustable Angle Footrest Adjusting Footplate Depth Adjusting Footplate Angle Replacing/Adjusting Optional Adjustable Angle Footrest Adjustments Clamp Arms Installing the Swingaway Padded Armrest Socket Remove Back Stop Insert Left Side Armrest Socket Right Side Armrest Socket Install Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Installing/Removing/Adjusting the Swingaway Padded Armrest Adjusting HeightRemoving Adjusting T-Arm Height  To remove the T-arm, reverse this procedure Unfolding/Folding the Back Back Detail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail Square will align with Hole in adjustmentWhen installed This orientation Seat Rail Orientation Hole AdjustmentSquare will align with + when installed With 0 when Back Upholstery Cover Adjustable Tension Back Upholstery Adjusting the Back Tension Removing the Lumbar Strap Removing the Adjustable Tension Back UpholsteryInstalling the Lumbar Strap Removing the Back Upholstery Cover Installing the Back Upholstery Cover Installing the Adjustable Tension Back Upholstery Back Canes Detail a Detail B Detail E Front Wheelchair Removing/Installing Foldover Back UpholsteryInstalling Foldover Back Upholstery Removing Foldover Back Upholstery HOLE* Number Back Height Adjustment Adjustment Pin Back Cane Hole NumberInsert Back Cane Installing Removing/Installing the Back Frame Replacing Seat Upholstery Seat Changing Seat Angle/Changing Rear Seat Height Bottom View Height Adjustment Bar Replacing the Wheel Lock Replacing/Adjusting the Wheel LocksAdjusting the Wheel Lock Wheel Locks Changing Wheel Lock Handle Position Replacing/Adjusting the Wheel Locks Converting From Pull-to-Lock to Push-to-Lock Configuration Wheels Removing/Installing Rear Wheels Removing/Installing Rear Wheels Adjusting Quick-Release Axles Adjusting Quad-Release Handles Replacing Quad-Release AxlesAnd/or Out Adjusting Quad-Release Handle In and/or Out Removing Play from Rear WheelsRemoving Play from Rear Wheels Handrim Replacement Handrim Replacement Determining Wheelbase Length Adjusting Wheelbase Length Adjusting Center of Gravity COG Wheels Mounting Screws Locknuts Frame Height Adjustment Bar May be affected Adjusting Wheelbase Width Removing/Installing the Camber Tube Installing the Camber TubeRemoving the Camber Tube Angle AxleCamber Tube Clamp Detail a Side View Adjusting the Camber Tube  For this procedure, refer to on page 76 and Figure Determining/Setting Toe In/Toe Out Top View of Wheelchair Top View of Wheelchair Caster Adjusting Fork Tension Detail a Detail B ONE Standard Fork Sided Fork Removing Front Caster Removing/Installing/Repositioning the Caster AssembliesInstalling Front Caster Standard Forks One Sided Fork Installing the CasterRemoving/Installing the Fork Assembly Removing Fork Assembly  Spacer orientation must be as shown in Figure Installing Fork Assembly  For this procedure, refer to on Repositioning the Front Caster Housings Caster Housing Angle Adjustment Small Angle AdjustmentsBelleville Washer Round Adjustment Nut Large Angle Adjustments Interference between Anti-Tipper Adjusting/Replacing Anti-tipper Replacing Anti-tipper Adjusting Anti-tipper Lock Buttons Release Buttons ANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair Canada USA