Standard Forks, Removing Front Caster | Invacare 1171880 specification

12CASTER

12.2Removing/Installing/Repositioning the Caster Assemblies

If replacing a front caster note the mounting position of the existing front caster for installation of the new front caster.

Both front casters MUST be the same size and adjusted to the same height.

Standard Forks

Removing Front Caster

1.Remove the mounting bolt, axle spacers and locknut that secure the front caster to the fork.

2.Remove the caster from the fork.

Installing Front Caster

1.Using the mounting bolt, axle spacers and locknut, secure the caster to the desired caster mounting position.

ForkLocknut

Mounting Bolt

Caster

Axle Spacer

Axle Spacer

FIGURE 2 Removing/Installing/Repositioning the Caster Assemblies

- Standard Forks

Invacare®Top End Reveal™Wheelchair

82

Part No 1171880

Image 82

Invacare 1171880 user manual Removing/Installing/Repositioning the Caster Assemblies, Standard Forks, Removing Front Caster

Contents

InvacareTop End RevealWheelchair Page Contents Seat Caster Symbols General Limited Warranty General Guidelines SafetyWheelchair User Wheelchair Tie Down Restraints Stability Warning Repair and Service Information Operating Information Seat Positioning Straps Weight TrainingTire Pressure and Information Overview Label Locations Serial Number Component Identification Non Tapered front end Standard Typical Product Parameters0, +4, +8 Lock Down, Folding Standard Reveal RVL Weight Safety/Handling of Wheelchairs Safety/Handling of WheelchairsStability and Balance SAFETY/HANDLING of Wheelchairs Lengthening Wheelbase Shortening Reaching, Leaning and Bending Forward Reaching, Leaning Bending Forward Backwards Reaching, Leaning BackwardsCoping with Everyday Obstacles Tipping Tipping Curbs Stairways Moving Up Stairs Moving Down Stairs Stairways Escalators Transferring To and From Other Seats Safety Inspection Checklist Safety InspectionInspect Initially Inspect/Adjust Weekly Inspect/Adjust Monthly Inspect/Adjust Periodically Troubleshooting Solutions Maintenance Maintenance Safety Precautions Suggested Maintenance Procedures  Tire wear is excessive if Replacing/Repairing Rear Wheel Tire/Tube Replacing/Repairing Caster Tire/Tube Adjusting the Footrest Adjusting/Replacing Standard FootrestFootrest Replacing/Adjusting Optional Adjustable Angle Footrest Replacing the Footrest Adjusting Footplate Angle Adjusting Footplate Depth Adjustments Clamp Replacing/Adjusting Optional Adjustable Angle Footrest Installing the Swingaway Padded Armrest Socket Arms Remove Back Stop Insert Right Side Armrest Socket Left Side Armrest Socket Install Back Stop Insert/Arm Socket Assembly Split Ring Back Release Cord Adjusting Height Installing/Removing/Adjusting the Swingaway Padded ArmrestRemoving  To remove the T-arm, reverse this procedure Adjusting T-Arm Height Back Unfolding/Folding the Back Detail a Folding the Back Back Angle Adjustment Repeat Steps 2-6 for remaining back cane Detail This orientation Hole in adjustmentWhen installed Square will align with With 0 when Hole AdjustmentSquare will align with + when installed Seat Rail Orientation Adjustable Tension Back Upholstery Back Upholstery Cover Adjusting the Back Tension Removing the Back Upholstery Cover Removing the Adjustable Tension Back UpholsteryInstalling the Lumbar Strap Removing the Lumbar Strap Installing the Adjustable Tension Back Upholstery Installing the Back Upholstery Cover Detail a Detail B Back Canes Detail E Removing Foldover Back Upholstery Removing/Installing Foldover Back UpholsteryInstalling Foldover Back Upholstery Front Wheelchair Back Height Adjustment HOLE* Number Hole Number Adjustment Pin Back CaneInsert Back Cane Removing/Installing the Back Frame Installing Seat Replacing Seat Upholstery Changing Seat Angle/Changing Rear Seat Height Height Adjustment Bar Bottom View Wheel Locks Replacing/Adjusting the Wheel LocksAdjusting the Wheel Lock Replacing the Wheel Lock Replacing/Adjusting the Wheel Locks Changing Wheel Lock Handle Position Configuration Converting From Pull-to-Lock to Push-to-Lock Removing/Installing Rear Wheels Wheels Adjusting Quick-Release Axles Removing/Installing Rear Wheels Replacing Quad-Release Axles Adjusting Quad-Release HandlesAnd/or Out Removing Play from Rear Wheels Adjusting Quad-Release Handle In and/or OutRemoving Play from Rear Wheels Handrim Replacement Handrim Replacement Adjusting Wheelbase Length Adjusting Center of Gravity COG Determining Wheelbase Length Wheels Mounting Screws Locknuts Frame Height Adjustment Bar Adjusting Wheelbase Width May be affected Installing the Camber Tube Removing/Installing the Camber TubeRemoving the Camber Tube Axle AngleCamber Tube Clamp Adjusting the Camber Tube Detail a Side View Determining/Setting Toe In/Toe Out  For this procedure, refer to on page 76 and Figure Top View of Wheelchair Top View of Wheelchair Adjusting Fork Tension Caster Detail a Detail B ONE Standard Fork Sided Fork Standard Forks Removing/Installing/Repositioning the Caster AssembliesInstalling Front Caster Removing Front Caster Removing Fork Assembly Installing the CasterRemoving/Installing the Fork Assembly One Sided Fork Installing Fork Assembly  Spacer orientation must be as shown in Figure Repositioning the Front Caster Housings  For this procedure, refer to on Small Angle Adjustments Caster Housing Angle AdjustmentBelleville Washer Round Adjustment Nut Large Angle Adjustments Interference between Adjusting/Replacing Anti-tipper Anti-Tipper Adjusting Anti-tipper Replacing Anti-tipper Release Buttons Lock Buttons ANTI-TIPPERS Bracket Setting For Higher Camber Tube Reversing Anti-tipper Bracket Orientation Reversing Anti-tipper Bracket Orientation InvacareTop End RevealWheelchair USA Canada