Husqvarna YTH20F42T To USE Cruise Control -J See Fig, To Adjust Mower Cutting Height See Fig

Page 10

OPERATION

TO USE CRUISE CONTROL -J (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield (S) in place.

S

FIG. 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH20F42T General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents To Remove Tractor from Carton AssemblyUnassembled Parts Unpack CartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Reverse Operation System ROS on PositionStopping HOW to USE Your TractorTo SET Parking BRAKESee Fig To USE Throttle Control D See FigTo USE Cruise Control -J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterBefore Starting the Engine To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Maintenance Before Each USEBrake Operation BatteryTractor TiresEngine Muffler CleaningEngine OIL Filter Spark PlugsTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig To Level Mower To Replace Mower Drive Belt See Fig Mower Drive Belt InstallationMower Drive Belt Removal Front Wheel TOE-IN/CAMBER To Replace Motion Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See FigTo Replace Headlight Bulb Replacing Battery See FigTo Start Engine with a Weak Battery See Fig Interlocks and RelaysTo Adjust Choke Control To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Schematic Tractor Model NO. YTH20F42T 96043000500, Product no 43Electrical KEY Part NO. NO. Description Chassis KEY Part Description Drive KEY Part NO. NO. Description Steering Assembly Tractor Model NO. YTH20F42T 96043000500, Product no 43 Seat Assembly Decals Wheels and TiresEngine KEY Part NO. NO. Description Mower Deck KEY Part Description Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement

YTH20F42T specifications

The Husqvarna YTH20F42T is a versatile and efficient riding lawn mower designed to meet the demands of residential lawn care. With its robust construction and user-friendly features, this model has gained popularity among homeowners looking for a reliable mowing solution.

At the heart of the YTH20F42T is a powerful 20 horsepower Kohler engine, providing ample power to tackle various terrain types. This engine not only ensures efficient mowing but also enhances overall durability and longevity. The automatic hydrostatic transmission allows for seamless speed adjustments and smooth transitions, making it easy to navigate around obstacles and varying landscape features.

One standout feature of the Husqvarna YTH20F42T is its 42-inch cutting deck, which strikes an ideal balance between maneuverability and cutting capacity. This deck size allows users to cover more ground in less time, making it suitable for medium to large-sized yards. The cutting height can be easily adjusted from 1.5 to 4 inches, giving users the flexibility to achieve their desired lawn appearance.

The mower is equipped with a washout port, facilitating quick and simple cleaning of the cutting deck. This feature enhances the mower’s maintenance routine, ensuring it operates efficiently and prolonging the life of the blades. Additionally, the mulching capability allows for nutrient recycling, promoting a healthier lawn while reducing the need for bagging grass clippings.

Comfort is not overlooked in the design of the YTH20F42T. It features an ergonomic seat with good back support, designed to keep users comfortable even during extended mowing sessions. The steering wheel is also positioned for easy access and control, enhancing the overall user experience.

Safety features, such as the automatic shutoff when the operator leaves the seat, provide peace of mind while operating the mower. The headlights ensure visibility during early morning or late evening mowing, making this mower a reliable choice any time of day.

In summary, the Husqvarna YTH20F42T combines power, efficiency, and comfort, making it an excellent choice for homeowners looking to maintain their lawns with ease. From its reliable engine to innovative features, this riding mower stands out as a go-to solution for effective lawn care.
Top Page Image Contents