To Replace Mower Blade Drive Belt See Fig

SERVICE AND ADJUSTMENTS

FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure dis- tance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D" "D"

FIG. 24

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

FRONT LINKS	TRUNNION
	TRUNNION
	FIG. 25

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 26)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

MANDRELIDLER

PULLEY PULLEYS

MANDREL

PULLEY

FIG. 26

TO ADJUST BRAKE (See Fig. 27)

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.

•Depress clutch/brake pedal and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center/department.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16"

JAM NUT

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER

BRAKE ADJUSTMENT IS NECESSARY

CONTACT YOUR NEAREST AUTHORIZED

SERVICE CENTER/DEPARTMENT

FIG. 27

TO ADJUST ATTACHMENT CLUTCH (See Fig. 28)

The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required. Adjustments should be made by your nearest authorized service center/department.