Husqvarna YT1942T owner manual Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 20

SERVICE AND ADJUSTMENTS

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

FIG. 28

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

FIG. 29

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents YT1942T Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Figs To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Move Forward and Backward See FigBefore Starting the Engine Mowing Tips To Start Engine See FigMaintenance Lubrication ChartBlade Removal See Fig BatteryTractor Engine To Remove Mower See Fig Service and AdjustmentsCleaning To Install Mower See Figs Slide mower out from under right side of tractorTo Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Drive Belt See FigTo Check Brake To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Schematic Tractor - Model Number YT1942T 96043000300, Product no 43Electrical KEY Part Description Chassis Steering Assembly Drive 155Transaxle, Peerless Engine Spark Arrester KITMower Lift 532 19 Shaft Asm., LiftSeat Assembly 532 19 SeatDecals Wheels and TiresMower Deck Mower Deck Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation 532 40 19-72 Rev 05.24.06 TR/VB/TR
Top Page Image Contents