Husqvarna 435e Maintenance schedule, Daily maintenance Weekly maintenance Monthly maintenance

Page 38

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

	Daily maintenance	Weekly maintenance	Monthly maintenance

		On chain saws without a catalytic	Check the brake band on the chain
		On chain saws without a catalytic	brake for wear. Replace when less
	Clean the outside of the machine.	converter, check the cooling system	brake for wear. Replace when less
	Clean the outside of the machine.	converter, check the cooling system	than 0.024 inch (0.6 mm) remains at
		weekly.	than 0.024 inch (0.6 mm) remains at
		weekly.	the most worn point.
			the most worn point.

	Check that the components of the	Check the starter, starter cord and	Check the clutch centre, clutch drum
	throttle control work safely. (Throttle	Check the starter, starter cord and	Check the clutch centre, clutch drum
	throttle control work safely. (Throttle	return spring.	and clutch spring for wear.
	lockout and throttle control.)	return spring.	and clutch spring for wear.
	lockout and throttle control.)

	Clean the chain brake and check that it
	operates safely. Make sure that the	Check that the vibration damping	Clean the spark plug. Check that the
	chain catcher is undamaged, and	elements are not damaged.	electrode gap is 0.020 inch (0.5 mm).
	replace it if necessary.

	The bar should be turned regularly for
	more even wear. Check the lubrication
	hole in the bar, to be sure it is not	Lubricate the clutch drum bearing.	Clean the outside of the carburetor.
	clogged. Clean the bar groove. If the	Lubricate the clutch drum bearing.	Clean the outside of the carburetor.
	clogged. Clean the bar groove. If the
	bar has a sprocket tip, this should be
	lubricated.

	Check that the bar and chain are	File off any burrs from the edges of the	Check fuel hose for cracks or other
	getting sufﬁcient oil.	bar.	damage. Change if necessary.

	Check the saw chain with regard to
	visible cracks in the rivets and links,
	whether the saw chain is stiff or	Clean or replace the spark arrestor	Empty the fuel tank and clean the
	whether the rivets and links are	screen on the mufﬂer.	inside.
	abnormally worn. Replace if
	necessary.

	Sharpen the chain and check its
	tension and condition. Check the drive	Clean the carburetor compartment.	Empty the oil tank and clean the
	sprocket for excessive wear and	Clean the carburetor compartment.	inside.
	sprocket for excessive wear and		inside.
	replace if necessary.

	Clean the starter units air intake.	Clean the air ﬁlter. Replace if	Check all cables and connections.
	Clean the starter units air intake.	necessary.	Check all cables and connections.
		necessary.

	Check that nuts and screws are tight.

	Check that the stop switch works
	correctly.

	Check that there are no fuel leaks from
	the engine, tank or fuel lines.

	On chain saws with a catalytic
	converter, check the cooling system
	daily.

38 – English

115 10 81-95 Rev.1 2008-01-08

Image 38

Contents 445 445e 450e Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will ﬁnd the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherVibration damping system Stop switchRight hand guard MufﬂerCutting equipment designed to reduce kickback Cutting equipmentGeneral rules BarSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethAdjustment of depth gauge setting General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Too large445 Tensioning the chainBar and cause serious or even fatal injury 445e, 450eChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication 445 AssemblyFitting the bar and chain 445e, 450e115 10 81-95 Rev.1 Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Stopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Checking the inertia brake release Mufﬂer Tensioning the recoil spring StarterReplacing the starter cord Fitting the starter Air ﬁlterReplacing the return and drive springs Recoil spring aNeedle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain ﬁling and ﬁle gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Kickback safety precautionsPage 1151081-95