Husqvarna 435e, 440e manual General Safety Precautions, Before using a new chain saw

Page 6

GENERAL SAFETY PRECAUTIONS

Before using a new chain saw

•Please read this manual carefully.

•Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly.

•Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping.

•Do not use the chain saw until sufficient chain oil has reached the chain. See instructions under the heading Cutting equipment.

•Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection.

WARNING! Under no circumstances may

! the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty may not cover damage or liability caused by the use of non- authorized accessories or replacement parts.

WARNING! A chain saw is a dangerous

! tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is very important that you read and understand the contents of this operator’s manual.

WARNING! The inside of the muffler

! contain chemicals that may be carcinogenic. Avoid contact with these elements in the event of a damaged muffler.

WARNING! Long term inhalation of the

! engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk.

WARNING! The ignition system of this

! machine produces an electromagnetic field during operation. This field may under some circumstances interfere with pacemakers. To reduce the risk of serious or fatal injury, we recommend persons with pacemakers to consult their physician and the pacemaker manufacturer before operating this machine.

WARNING! Never allow children to use or

! be in the vicinity of the machine. As the machine is equipped with a spring- loaded stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the machine. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the machine is not under close supervision.

Important

IMPORTANT!

The machine is only designed for cutting wood.

You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data.

Never use the machine if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affect your vision, alertness, coordination or judgement.

Wear personal protective equipment. See instructions under the heading Personal protective equipment.

Do not modify this product or use it if it appears to have been modified by others.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading Maintenance.

Never use any accessories other than those recommended in this manual. See instructions under the headings Cutting equipment and Technical data.

CAUTION! Always wear protective glasses or a face visor to reduce the risk of injury from thrown objects. A chain saw is capable of throwing objects, such as wood chips, small pieces of wood, etc, at great force. This can result in serious injury, especially to the eyes.

WARNING! Running an engine in a

! confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning.

WARNING! Faulty cutting equipment or

! the wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

6 – English

115 10 81-95 Rev.1 2008-01-08

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 445 445e 450e Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherVibration damping system Stop switchRight hand guard MufflerCutting equipment designed to reduce kickback Cutting equipmentGeneral rules BarSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethAdjustment of depth gauge setting General advice on adjusting depth gauge settingIncreased if the depth gauge setting is Too large445 Tensioning the chainBar and cause serious or even fatal injury 445e, 450eLubricating cutting equipment Filling with chain oilChecking chain lubrication Chain drive sprocket Needle bearing lubricationChecking wear on cutting equipment 445 AssemblyFitting the bar and chain 445e, 450e115 10 81-95 Rev.1 Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting and Stopping Starting and stoppingStarting Stopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut How to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the inertia brake release Muffler Starter Replacing the starter cordTensioning the recoil spring Fitting the starter Air filterReplacing the return and drive springs Recoil spring aNeedle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemAir Injection centrifugal cleaning Temperature -5C 23F or colderWinter use Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw Kickback safety precautionsPage 1151081-95
Top Page Image Contents