Husqvarna LTH1536 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSt-

MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place motion control lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 14)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRAC- TOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 14)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

SMALL RETAINER SPRING

 

CLUTCH SPRING

SQUARE HOLE

 

FLAT WASHER

 

SUSPENSION ARMS

ENGINE PULLEY

SMALL RETAINER SPRING

 

 

FRONT LINK

CLUTCH SPRING

 

RETAINER SPRING

RETAINER SPRINGS

 

ANTI-SWAY BAR

(BOTH SIDES)

 

BRACKET

 

COLLAR

DEFLECTOR SHIELD

 

HOUSING GUIDE

 

 

02694

 

LARGE RETAINER SPRING

FIG. 14

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents LTH1536 II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat KeyTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorConnect Battery See Figs a and 3B Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig Stopping See Fig To SET Parking Brake See FigTo Transport See Figs Before Starting the EngineTo Operate Mower See Fig To Operate on HillsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Muffler CleaningAIR Filter Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Adjust Steering Wheel AlignmentTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Tractor Model NO. LTH1536 HAU15HK36B, Product no 17 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures 532 19 18-14 Dash P/L Drive CRD KEY Part DescriptionSteering Assembly KEY Part NO. NO. Description Engine Repair Parts Seat Assembly Wheels & Tires DecalsMower Deck Repair Parts Mower Lift Repair Parts Service Notes Service Notes Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 19 20-12 03.05.04 TR
Top Page Image Contents