Husqvarna LTH1742 To Replace Motion Drive Belt See Fig, To Check Brake, To Adjust Brake

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

Depress clutch/brake pedal all the way down and en- gage parking brake.

Measure distance between brake operating arm and nut “A” on brake rod.

If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

Engage transmission by placing freewheel control in “transmission engaged” position.

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER

BRAKE ADJUSTMENT IS NECESSARY CON-

TACT YOUR NEAREST AUTHORIZED SERVICE

CENTER/DEPARTMENT

FIG. 22

TO REPLACE MOTION DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler and clutching idler.

Remove belt downward from around engine pulley.

21

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down around transmission cooling fan and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll around the top groove of engine pulley.

Install belt through stationary idler and clutching idler.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

FIG. 23

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 24)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral (N) (lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satis- fied.

Image 21
Contents LTH1742 Safe Operation Practices for Ride-On Mowers IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsKey Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from CAR- TON Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Tire Pressure To Convert to Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Before Starting the EngineTo Operate on Hills To Transport See FigsTo Start Engine See Fig ADD GasolinePurge Transmission Automatic Transmission Warm UPMulching Mowing Tips Mowing TipsLubrication Chart MaintenanceService Dates General RecommendationsTractor Engine Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust CarburetorInterlocks and Relays To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model NO. LTH1742 LTH1742A, Product no 57 SchematicElectrical KEY Part Description Chassis and Enclosures 532 17 46-19 Chassis Stamping Drive CRD Steering Assembly Repair Parts 532 14 Seat Seat AssemblyWheels & Tires DecalsEngine Repair Parts Mower Deck Repair Parts Mower Lift Repair Parts Service Notes Service Notes Warranty Statement Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation532 18 44-93 11.20.02 RH

LTH1742 specifications

The Husqvarna LTH1742 is a standout in the realm of riding lawn mowers, designed to deliver both performance and comfort for homeowners managing medium to large lawns. With its robust build and user-friendly features, it ensures a seamless mowing experience that meets the demands of any yard.

One of the key features of the LTH1742 is its powerful engine. Equipped with a 17-horsepower Briggs and Stratton engine, this mower provides ample power to handle tough grass and uneven terrain. The reliable four-stroke engine ensures efficient fuel consumption while producing the necessary torque for effective cutting even in challenging conditions.

The 42-inch cutting deck is another significant characteristic of the Husqvarna LTH1742. Its size strikes a balance between maneuverability and mowing efficiency, allowing users to cover a wider area in less time. The deck features a robust steel construction for durability, and the cutting height can be easily adjusted from 1 to 4 inches using a convenient lever, catering to various grass types and user preferences.

To enhance the mowing experience, the LTH1742 incorporates hydrostatic transmission. This technology provides the operator with smooth and precise control over speed and direction, allowing for effortless navigation around obstacles and tight corners. The automatic drive system eliminates the need for gear shifting, making it accessible for users of all experience levels.

Comfort is also a focal point of the Husqvarna LTH1742. It comes equipped with an ergonomic seat that offers ample support, ensuring that users can mow for extended periods without discomfort. The easy-to-reach controls and intuitive dashboard further enhance user experience, allowing for quick adjustments without needing to divert attention from the mowing process.

Another notable feature includes the ease of maintenance. The mower is designed with a washout port that makes cleaning the cutting deck a straightforward task, prolonging the equipment's lifespan and maintaining optimal performance. Additionally, the LTH1742 offers a variety of accessories, enabling users to customize their mower for different tasks, such as mulching or bagging.

In summary, the Husqvarna LTH1742 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its powerful engine, adjustable cutting deck, hydrostatic transmission, and attention to operator comfort solidify its place as a reliable and effective lawn care solution.