Husqvarna LTH1742 Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 22

SERVICE AND ADJUSTMENTS

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 25)

TO START ENGINE WITH A WEAK BATTERY (See Fig. 26)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 25

FIG. 26

REPLACING BATTERY (See Figs. 27 and 28)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

22

Image 22
Contents LTH1742 General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationSafety Rules Table of Contents Key Unassembled PartsSteering Wheel Seat Slope SheetTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Mulching Mowing TipsService Dates MaintenanceLubrication Chart General RecommendationsTractor Engine Muffler CleaningClean AIR INTAKE/COOLING Areas Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal To Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Check BrakeReplacing Battery See Figs Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model NO. LTH1742 LTH1742A, Product no 57Electrical KEY Part Description Chassis and Enclosures 532 17 46-19 Chassis Stamping Drive CRD Steering Assembly Repair Parts Seat Assembly 532 14 SeatDecals Wheels & TiresEngine Repair Parts Mower Deck Repair Parts Mower Lift Repair Parts Service Notes Service Notes Warranty Statement Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX532 18 44-93 11.20.02 RH

LTH1742 specifications

The Husqvarna LTH1742 is a standout in the realm of riding lawn mowers, designed to deliver both performance and comfort for homeowners managing medium to large lawns. With its robust build and user-friendly features, it ensures a seamless mowing experience that meets the demands of any yard.

One of the key features of the LTH1742 is its powerful engine. Equipped with a 17-horsepower Briggs and Stratton engine, this mower provides ample power to handle tough grass and uneven terrain. The reliable four-stroke engine ensures efficient fuel consumption while producing the necessary torque for effective cutting even in challenging conditions.

The 42-inch cutting deck is another significant characteristic of the Husqvarna LTH1742. Its size strikes a balance between maneuverability and mowing efficiency, allowing users to cover a wider area in less time. The deck features a robust steel construction for durability, and the cutting height can be easily adjusted from 1 to 4 inches using a convenient lever, catering to various grass types and user preferences.

To enhance the mowing experience, the LTH1742 incorporates hydrostatic transmission. This technology provides the operator with smooth and precise control over speed and direction, allowing for effortless navigation around obstacles and tight corners. The automatic drive system eliminates the need for gear shifting, making it accessible for users of all experience levels.

Comfort is also a focal point of the Husqvarna LTH1742. It comes equipped with an ergonomic seat that offers ample support, ensuring that users can mow for extended periods without discomfort. The easy-to-reach controls and intuitive dashboard further enhance user experience, allowing for quick adjustments without needing to divert attention from the mowing process.

Another notable feature includes the ease of maintenance. The mower is designed with a washout port that makes cleaning the cutting deck a straightforward task, prolonging the equipment's lifespan and maintaining optimal performance. Additionally, the LTH1742 offers a variety of accessories, enabling users to customize their mower for different tasks, such as mulching or bagging.

In summary, the Husqvarna LTH1742 combines power, efficiency, and user-friendly features, making it an excellent choice for homeowners looking to maintain their lawns with ease. Its powerful engine, adjustable cutting deck, hydrostatic transmission, and attention to operator comfort solidify its place as a reliable and effective lawn care solution.