Husqvarna LGTH2454 owner manual Tractor, Blade Care, Blade Removal See Fig, Battery

Page 18

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 27)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

• When the engine is running, any attempt by the operator

to leave the seat without first setting the parking brake

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 28)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

 

CENTER HOLE

should shut off the engine.

• When the engine is running and the attachment clutch

BATTERY

Fig. 28

is engaged, any attempt by the operator to leave the

seat should shut off the engine.

• The attachment clutch should never operate unless

the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 27

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Raise hood.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICEANDADJUSTMENTSsectionofthismanual).

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents LGTH2454 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonTo Install Mower and Drive Belt See Figs To Check Battery See FigAdjust Seat See Fig Before Removing Tractor from SkidTurn Steering Wheel Left and Position Mower See Fig Install ANTI-SWAY BAR S if Equipped SeeAssemble Front Gauge Wheel W to Front of Mower See Fig Slide Mower Under Tractor See FigAttach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigAttach Front Link E See Fig Check Deck Levelness Install Belt on Engine Clutch Pulley M SeeCheck Tire Pressure Check for Proper Position of BeltsOperation Know Your Tractor DPH AC JTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterReverse Operation System ROS To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigTransaxle Cooling Clean AIR ScreenBelts Transaxle Pump FluidCleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Replace Mower Blade Drive Belt See FigTo Level Mower To Replace Motion Drive Belt See Fig Transaxle Motion Control Lever Neutral Adjustment See FigBelt Installation To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission EngineFuel System StorageOther Engine OILHard to start Loss of powerWill not start Engine will notFires when turn To run when operBattery will not Engine continuesSchematic Tractor Model NO. LGTH2454 96043010700, Product no 43Tractor Model NO. LGTH2454 96043010700, Product no 43 Electrical KEY Part DescriptionChassis Tractor Model NO. LGTH2454 96043010700, Product no 43 Drive Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr Engine Engine Kawa Model No. FR691V-AS06 Steering Assembly Seat Assembly 532 42 SeatMower Deck 532 40 31-25 Deck Weldment Mower Mower Lift Decals Wheels and TiresLimitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Suggested Guide for Sighting Slopes for Safe Operation Service Notes Service Notes Service Notes 05.24.10 JA

LGTH2454 specifications

The Husqvarna LGTH2454 is a versatile and powerful lawn tractor designed to provide excellent cutting performance and user comfort. With its robust construction and advanced features, it is ideal for homeowners with medium to large-sized yards. The LGTH2454 stands out for its powerful engine, user-friendly operation, and enhanced mowing capabilities, making it a reliable choice for lawn care enthusiasts.

At the heart of the LGTH2454 is its 24 HP Kohler engine, known for its durability and efficient performance. This powerful engine delivers consistent power to the cutting deck, ensuring a clean and even cut every time. The automatic transmission allows for smooth speed adjustments, providing an effortless driving experience whether you’re mowing on flat terrain or tackling slight inclines.

One of the standout features of the LGTH2454 is its 54-inch cutting deck. The wide cutting path not only helps to reduce mowing time but also allows for efficient coverage of large areas. The cutting height can be easily adjusted from 1.5 to 4 inches, providing flexibility for different grass types and mowing conditions. The reinforced cutting deck design ensures durability, while the air-induction technology enhances airflow within the deck for superior grass lift and cutting performance.

Comfort is a key focus in the design of the LGTH2454. The high-back seat is ergonomically designed to provide support during extended mowing sessions. Coupled with an adjustable steering wheel, it allows operators to customize their seating position for optimal comfort. The easy access controls streamline operation, ensuring that users can focus on mowing without fumbling with complicated settings.

The LGTH2454 also features an innovative cutting system that enables mulching, bagging, or side discharge, making it adaptable to various lawn care needs. The mulching kit recycles clippings back into the lawn, promoting healthier grass growth, while the bagging option collects grass for easy disposal.

Additional technologies such as the LED headlights enhance visibility during early morning or late afternoon mowing, enabling users to work in various lighting conditions. The rugged tires provide excellent traction, ensuring stability on uneven ground.

In conclusion, the Husqvarna LGTH2454 is a top-tier lawn tractor that combines power, versatility, and comfort. Its robust engine, wide cutting deck, and user-centric design make it an appealing choice for anyone looking to maintain a beautiful lawn with ease and efficiency. Whether you’re a seasoned gardener or a novice homeowner, the LGTH2454 is equipped to meet your lawn care needs.
Top Page Image Contents